Motorcycle ignition system
Jawa TS 350
Manufacturer
Price
Sort
Products reviews
2019-09-19, 12:32
Sebastian
I own a jawa 50 ogar 200 moped.I purchased an ignition coil for this model and am very pleased with the product. Well made, safely packaged and, of course, efficient. After installation the jawka fired up and I can still enjoy the ride. I highly recommend the product and gmoto.pl store for their professional service and low parts prices.
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2019-04-12, 17:56
Franciszek
I put the coil on the MZ 250.2 ES TROPHY, late last autumn, so that the motorcycle, practically was already in "winter sleep". When I started riding with the new coil in March this year, unpleasant events began to happen, as the motorcycle had difficulty firing up, and while riding, unexpectedly stopped working. After a while, it was again somehow possible to start the engine, but the ride was uneventful, and I finally put the motor in the garage to determine the cause of the problems. Somewhat accidentally, I brought my hand close to the area of the coil when the motorcycle briefly fired up, and I nearly fell to the ground due to an electric shock, which instead of the spark in the spark plug, accumulated on my person. I don't know if this new coil had a puncture from the beginning, but it certainly does now. So, after using it for a short time, I know that this coil, is not suitable for operation. It brought me a lot of worry, because I did not suspect that a new product, could be so unreliable. Refers to the purchase of November 2018 - order 497413
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2017-11-14, 17:21
Mariusz
WSK 175 coil gives spark but the engine did not run properly. I put it in another motorcycle and the same thing, the engine only ran at idle and when I added gas it did not go into higher revs. After installing a used PRL coil, the moto runs without problems. Be careful, a new part and there is no assurance that the engine will work properly.
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2019-07-07, 20:22
Bartłomiej
Bolts for the installation of platinums have too large a diameter. To assemble the ignition you need to grind the hole of the "anvil" minimally, the hammer fits ok. The hole of the anvil (for the screws for adjusting the gap behind the platynes) too small/poorly profiled, you need to grind with a small file to freely adjust everything.
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2022-01-22, 10:01
DAWID
I RECOMMEND THAT YOU DO NOT HESITATE TO CONTACT ME ON THE OLD CEFCE THERE WAS A WEAK SPARK AND WE WERE LOOKING FOR THE CAUSE NOW AFTER REPLACING IT WITH THIS ONE THERE IS A VERY VISIBLE AND STRONG STABLE SPARK I RECOMMEND THAT IN MY CASE THE PROBLEMS WITH THE SPARK DISAPPEARED DURING REPAIRS WITH THE ELECTRICIAN EVERYONE SHOULD CHANGE IT FOR PEACE OF MIND AND CORRECT SPARK
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2018-02-19, 10:51
Piotr
Hello I have a lot of motorcycles in my garage, currently I am dealing with Jawa 350Ts, the installation went without a problem Jawa runs without any complaints .The next motorcycle in my plan to restore will be a 1976 Kmar Sport and I will certainly buy some parts in your store greetings
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2023-07-23, 06:27
Łukasz
First, I bought elsewhere a supposedly original coil for 300 zł. It turned out that it worked for 2 hours and that was it I decided to buy a replacement, so far since Friday it works flawlessly.
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2020-06-17, 00:05
Artur
Warning. Knitting almost nothing fits you have to saw with a file to fit, problems with setting the ignition because the screws when tightening present platens.
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2019-04-15, 10:57
Piotr
I do not recommend these flakes. Fixings Crooked. Probably a Chinese product. It is better to purchase original parts in this case.
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion