Motorcycle carburettor components
Qingqi QM50T-10A 50

2024-09-18, 07:22

View original

Richard

Ebonite carburettor washer with GY6 4T O-ring has not been installed, as the pipe is the wrong size

Review translated automatically

Reliable opinion

2021-07-07, 03:00

View original

JanD

Moped - Barton Fighter Eco 2020 The store's merchandise filter specified as if this pad would fit my machine. It does not fit!!! The main hole is 3.5 mm too small, and worse, the spacing of the screws is also strongly too small. I had an emergency situation and sanded the holes to my needs provisionally. But I am disappointed. For 139FMB engines, GMoto does not carry ebonite washers, despite the fact that these are the most common moped engines in Poland. And I see in the previous comments that this is nothing new.

Review translated automatically

Reliable opinion

2016-01-01, 15:35

View original

Krzysztof

What to write here a lot. I have a moped Romet C1 and it is always difficult to fit some parts to it. In the case of the handle, which I also ordered from this website, I succeeded, but not with the gasket. I do not see the point of sending it back, because it would be a terrible waste of bilge(

Review translated automatically

Reliable opinion

2020-12-07, 13:14

View original

Patryk

Hello I have a 4t 80cc scooter I ordered a repair kit for the scooter because my float and gas adjustment in the carburetor broke. I ordered this kit and it came as needed, now it runs like a dragon I recommend!

Review translated automatically

Reliable opinion

2019-06-06, 22:00

View original

Ostrowski

My machine is a 4t baotian 50cm scooter after tiuning now 72cm bigger nozzle bigger spigot necessary bigger spigot washer this product meets all the requirements I highly recommend it

Review translated automatically

Reliable opinion

2019-02-16, 09:37

View original

Adam

The pad is nicely made, it's a pity that it's made of poor materials, but for a few zlotys you can't expect miracles, but it's worth adding a few zlotys and buying a better one, best regards

Review translated automatically

Reliable opinion

2023-06-30, 17:10

View original

Maariusz

The spigot ok everything fit, so far it works because I already had cases with vacuums falling out while driving, they were sticking apart. We will see how long this one will work.

Review translated automatically

Reliable opinion

2017-05-31, 19:30

View original

Marek

I have a 2011 Router Bassa scooter. I needed from the kit only jets needle and spring. all parts fit. Only on the firing pin I had to increase the level ;)

Review translated automatically

Reliable opinion

2020-06-22, 18:06

View original

Łukasz

Nice service, everything as described, super packed and protected, fast shipping. Ebonite carburetor washer with oring super made I recommend this store.

Review translated automatically

Reliable opinion

2022-05-10, 07:24

View original

Bartłomiej

Moped Junak 901 50 cm, after changing from the original to this one, the engine finally began to run well super somehow does not break and I really recommend.

Review translated automatically

Reliable opinion

2017-06-25, 19:46

View original

Antoni

Washer bought as a replacement as a result of deformed rubber o-ring in the old one. All OK. Connection of the carburetor to the head tight.

Review translated automatically

Reliable opinion

2018-08-09, 10:32

View original

Piotr

Router bass 50 Goods compatible fast delivery Recommended store fast shipping , because with competitors you have to wait up to a week

Review translated automatically

Reliable opinion

2017-04-05, 08:07

View original

Bartłomiej

Romet 4t scooter. Washer ok almost like org actually it's org because it's also china :) but it does its job 100% also you can buy

Review translated automatically

Reliable opinion