Motorcycle engine - parts
Honda CB 250

2024-06-18, 09:23

View original

Miko

I do not recommend this plug absolutely. The plug did not withstand the first tightening with a torque wrench much before reaching the proper tightening torque. I can't tell where the positive comments under this product come from, maybe with larger diameter plugs it is better. In my case, a simple oil change ended up with a whole day of disassembling and putting the motorcycle back together to remove the broken thread and the magnesium that fell inside the oil pan. The fit itself is not right either, the original plug has more than twice the thread length.

Review translated automatically

Reliable opinion

2020-07-22, 14:30

View original

Kamil

Honda NX 500 Dominator 1988 It fits perfectly. It is solid and when it came in contact with the wrench cap, it did not behave like plasticine unlike the old screw. I have already done 1500 kilometers. All in good order. An interesting option with a magnetic tip. I recommend.

Review translated automatically

Reliable opinion

2018-08-20, 18:46

View original

Michał

Hello I own a Honda VTR1000 F 1997 I bought a mirror for a small amount of money which is durable, not like the Chinese crap that folds at higher speed and vibrates at slow speed. With a clear conscience I recommend Gmoto.pl store

Review translated automatically

Reliable opinion

2020-07-30, 12:06

View original

Darek

The screw is made with precision. I just pay attention to the assembly! The original screw is at least twice as long. The torque recommended in the service book (43Nm) is far too much for a Yamaha Thundercat, fekt is a broken thread.

Review translated automatically

Reliable opinion

2018-03-28, 21:08

View original

Piotr

1. bolt 12, which is a size 17? The threads fit, but. 2. it cracked while screwing leaving a piece of thread in the oil pan. 3. want to experience a heart attack during an oil change? Only 14.80!

Review translated automatically

Reliable opinion

2020-08-30, 17:52

View original

Michał

The screw is professionally made, it holds until nice. It certainly does not drop a drop. The magnet attached to its end is so strong that I had a hard time detaching it from the tool cart. I recommend

Review translated automatically

Reliable opinion

2021-01-13, 19:51

View original

Kuba

Good copper pad a lot of size options price good relative to the quality of workmanship well here I really order everything I need from gmoto and I am always satisfied.

Review translated automatically

Reliable opinion

2021-05-03, 09:49

View original

Młody

The thread of the plug ok and basically that's it. Unfortunately, the magnet practically does not do its job. It's a waste of money for this particular plug.

Review translated automatically

Reliable opinion

2018-03-10, 14:21

View original

Wiesław

EBC springs super quality for little money Super made fit perfectly in the slots I recommend the product

Review translated automatically

Reliable opinion

2020-02-25, 22:48

View original

Johan

For my Hondas FT 500 (1983) & XBR 500 (1986) as spares. Remove the lever first, then punch out the old one from the contact pins side; it's an easy, light press fit. When pressing in the new one, align the hook on the switch with the notch in the clutch lever body. Note the hole in the switch also lines up with a hole at the underside of the alu body; it's for contact spray when needed. (Better use it before needed; once corroded the inner contact becomes difficult).

Review translated automatically

Reliable opinion

2024-03-04, 06:42

View original

Łukasz

Affairs, it conducts electricity. However, it does not fit the 1976 GL1000 K1 model, as it has a larger diameter than the original (factory) and will not go into the hole in the handle holder. I had to take the original one apart despite the damage and was able to repair it. Perhaps this one will fit the specified GL1000 78-79 but I will check this when I give it to a colleague. It would be good to have the basic dimensions plotted on the parts in the photo to see if it will fit us.

Review translated automatically

Reliable opinion

2023-05-24, 10:46

View original

Dawid

A great copper washer for the oil drain bolt. Its main advantage is the right hardness. When tightening, it undergoes plastic deformation, so it perfectly fulfills its role - seals. Beware of washers made of copper alloys. Some of them are so hard that they do not yield even when hit with a hammer - they are not suitable for sealing the oil drain.

Review translated automatically

Reliable opinion

2018-05-11, 20:28

View original

Kamil

Honda Dominator NX650 If you are asking yourself whether it makes sense to buy motorcycle accessories by mail order, then calculate the time spent in traffic jams to drive to the stores in search of selected items. My calculation indicates that for a few zlotys it's not worth it to run the car. On Gmoto I found everything I need. Both the price and delivery time are exemplary. I recommend.

Review translated automatically

Reliable opinion

2021-02-07, 13:11

View original

RDS

Some time ago I began to apply the principle of replacing copper washers at the time of oil change (previously I burned out). I must admit that for 1 zl it is not worth fighting with the old washer, especially since you will not get the same effect as with a new one. Now I treat the washer as a mandatory set - I always buy a set of oil + filter + drain bolt washer.

Review translated automatically

Reliable opinion

2017-04-04, 18:03

View original

Grzegorz

My machines WSK M06B3 72r , Jawa 350 TS,Minsk 400, I have been sourcing parts from GMOTO for some time, I recommend because of the sufficient description of products, conformity of parts with the description, fast shipping, great contact. I am passionate about extinct motorcycles (demoluds to be precise), so I require a lot from the goods and here I find it,without unnecessary fuss.

Review translated automatically

Reliable opinion

2020-04-28, 07:30

View original

Witold

I own a 2008 Honda Varadero 125XL Motorcycle.For proper operation, it is necessary to change the oil in the engine at the beginning of each season. In these changes, the oil drain plug gasket should be replaced periodically. Good gaskets are copper gaskets, which I purchased from Gmoto.pl and their quality is very good at an attractive price. I recommend.

Review translated automatically

Reliable opinion

2024-09-19, 08:55

View original

BOULET-DESBAREAU

The product is very similar to the original. The only fault is that the threaded end is too short compared to the original. It's missing about 5 to 8 mm. This damaged the threads on my housing. I had to dismantle everything and redo the threading with ilsert.

Review translated automatically

Reliable opinion

2020-04-18, 09:48

View original

Łukasz

The pad does its job. The best part, however, is that the store has well-matched parts for the motorcycle model. With many sizes of washers, it's important to buy the right one so that when you drain the oil from the engine, you don't have to look for the right one. We use a new one and we're done ;)

Review translated automatically

Reliable opinion

2018-04-01, 13:06

View original

Łukasz

I use exactly this magnetic oil drain screw in every Honda I have. The screw, despite exposure to harsh weather conditions, does not corrode, does not catch deposits and, most importantly, does not leak. The magnet actually catches metallic flecks and does not lose strength.

Review translated automatically

Reliable opinion

2016-03-10, 07:31

View original

Szymon

A washer made of good copper. It fit under the drain bolt on the Honda CBR125R. Remember to warm up the engine before changing the oil. When the oil has already fried a sturdy bottom so that the washer does not come in contact with the old oil.

Review translated automatically

Reliable opinion

2023-08-18, 11:07

View original

Artur

Everything ok full professionalism and fast delivery ( everything original) plus for remembering the motorcycle on the website and selecting parts by the selected version I will definitely use this store in the future I recommend it

Review translated automatically

Reliable opinion

2020-11-22, 15:13

View original

Jacek

Yamaha XVS 1300 CU year 2014 The bolt is shorter than the original and does not hold the size of the original bolt. It should not be indicated to fit this model. The only use for it is a copper gasket.

Review translated automatically

Reliable opinion

2024-10-29, 16:46

View original

Dennis

It just fit perfectly on my Honda FT500. Gave it a little oil first, it didn't take much for the flywheel to come off.

Review translated automatically

Reliable opinion