Forgot password
Order status
Free delivery from 150 euro
Manufacturer
Price
Sort
€8.14
Shaft seal - 12015854B
€21.61
FLYWHEEL PULLER - 08-0086
Options +2 €68.71
Lowest price from 30 days before discount: €76.35
DID timing chain SCA0412ASV-110 open timing chain with lugs
(6) 
€13.88
Lowest price from 30 days before discount: €14.61
TRW Lucas MEF 115-6 clutch springs - MEF115-6
(1) 
€33.74
Lowest price from 30 days before discount: €35.52
A set of TRW Lucas MES 334-6 metal clutch discs. - MES334-6
€41.85
Lowest price from 30 days before discount: €44.06
A set of TRW Lucas MES 326-6 metal clutch discs. - MES326-6
(1) 
€5.08
Lowest price from 30 days before discount: €5.35
Athena alternator cover gasket - S410210017005
(1) 
€10.72
Lowest price from 30 days before discount: €11.28
Athena clutch cover gasket - S410210008123
(1) 
€13.50
Lowest price from 30 days before discount: €14.21
Athena valve cover gasket - S410210015021
(1) 
Browse by manufacturer
Products reviews
The screw is made with precision. I just pay attention to the assembly! The original screw is at least twice as long. The torque recommended in the service book (43Nm) is far too much for a Yamaha Thundercat, fekt is a broken thread.
Review translated automatically
Reliable opinion
Honda CB 400N 1983 Product very well made , high quality of material used and precise machining . I recommend replacing the o-ring every time you change the filter
Review translated automatically
Reliable opinion
For my Hondas FT 500 (1983) & XBR 500 (1986) as spares. Remove the lever first, then punch out the old one from the contact pins side; it's an easy, light press fit. When pressing in the new one, align the hook on the switch with the notch in the clutch lever body. Note the hole in the switch also lines up with a hole at the underside of the alu body; it's for contact spray when needed. (Better use it before needed; once corroded the inner contact becomes difficult).
Review translated automatically
Reliable opinion
Affairs, it conducts electricity. However, it does not fit the 1976 GL1000 K1 model, as it has a larger diameter than the original (factory) and will not go into the hole in the handle holder. I had to take the original one apart despite the damage and was able to repair it. Perhaps this one will fit the specified GL1000 78-79 but I will check this when I give it to a colleague. It would be good to have the basic dimensions plotted on the parts in the photo to see if it will fit us.
Review translated automatically
Reliable opinion
A great copper washer for the oil drain bolt. Its main advantage is the right hardness. When tightening, it undergoes plastic deformation, so it perfectly fulfills its role - seals. Beware of washers made of copper alloys. Some of them are so hard that they do not yield even when hit with a hammer - they are not suitable for sealing the oil drain.
Review translated automatically
Reliable opinion
Some time ago I began to apply the principle of replacing copper washers at the time of oil change (previously I burned out). I must admit that for 1 zl it is not worth fighting with the old washer, especially since you will not get the same effect as with a new one. Now I treat the washer as a mandatory set - I always buy a set of oil + filter + drain bolt washer.
Review translated automatically
Reliable opinion
My machines WSK M06B3 72r , Jawa 350 TS,Minsk 400, I have been sourcing parts from GMOTO for some time, I recommend because of the sufficient description of products, conformity of parts with the description, fast shipping, great contact. I am passionate about extinct motorcycles (demoluds to be precise), so I require a lot from the goods and here I find it,without unnecessary fuss.
Review translated automatically
Reliable opinion
The product is very similar to the original. The only fault is that the threaded end is too short compared to the original. It's missing about 5 to 8 mm. This damaged the threads on my housing. I had to dismantle everything and redo the threading with ilsert.
Review translated automatically
Reliable opinion
Everything ok full professionalism and fast delivery ( everything original) plus for remembering the motorcycle on the website and selecting parts by the selected version I will definitely use this store in the future I recommend it
Review translated automatically
Reliable opinion
Yamaha XVS 1300 CU year 2014 The bolt is shorter than the original and does not hold the size of the original bolt. It should not be indicated to fit this model. The only use for it is a copper gasket.
Review translated automatically
Reliable opinion
I recommend, everything nicely, aesthetically packed,protected and as described. After installation everything as ok. recommend
Review translated automatically
Reliable opinion
Fast delivery, excellent quality! Sterilely packed and clean, exactly the same as in the picture! The quality shows
Review translated automatically
Reliable opinion
The chain made very aesthetically pleasing all dimensions in accordance with the original without any problems fit the gears.
Review translated automatically
Reliable opinion
Honda CB 400 N year 1985, fits nicely nothing leaks :)
Review translated automatically
Reliable opinion
We have Motorcycle engine - parts to Honda CM 400
- Honda CM 400 T Custom 1983
- Honda CM 400 T 1980
- Honda CM 400 T 1981
- Honda CM 400 T Custom 1982
- Honda CM 400 T Custom 1984
- Honda CM 400 A Hondamatic 1979
- Honda CM 400 A Hondamatic 1980
- Honda CM 400 A Hondamatic 1981
- Honda CM 400 C Custom 1980
- Honda CM 400 E 1983
- Honda CM 400 E 1981
- Honda CM 400 E 1980
- Honda CM 400 T 1979
- Honda CM 400 A Twin Automatic 1981
- Honda CM 400 A Twin Automatic 1980