Forgot password
Order status
Free delivery from 150 euro
Manufacturer
Price
Sort
Options +4 
€12.16
Lowest price from 30 days before discount: €12.80
Athena bearing SKF 6303 2RSC3 17x47x14 mm - MS170470140M3
€21.61
FLYWHEEL PULLER - 08-0086
rozmiary:
€10.72
Lowest price from 30 days before discount: €11.28
TRW Lucas MEF 112-4 clutch springs - MEF112-4
€64.25
Lowest price from 30 days before discount: €71.39
DID SC0417DHA-78 closed timing chain - DIDSC0417DHA-78
(2) 
€71.20
Lowest price from 30 days before discount: €74.95
TRW Lucas MCC 119-8 clutch disc set. - MCC119-8
€74.12
Lowest price from 30 days before discount: €78.02
Top-End Athena engine gasket set - P400210600651
€72.11
Lowest price from 30 days before discount: €75.90
Top-End Athena Honda engine gasket set - P400210600600/1
Browse by manufacturer
Products reviews
I recommend the clutch pump repair kit from Tourmax. Replacement is trivially easy, and all the necessary things that wear out in such a pump are included in the set. For a small amount of money, you can easily recondition a malfunctioning pump and eliminate clutch problems.
Review translated automatically
Reliable opinion
The screw is made with precision. I just pay attention to the assembly! The original screw is at least twice as long. The torque recommended in the service book (43Nm) is far too much for a Yamaha Thundercat, fekt is a broken thread.
Review translated automatically
Reliable opinion
Honda CB 400N 1983 Product very well made , high quality of material used and precise machining . I recommend replacing the o-ring every time you change the filter
Review translated automatically
Reliable opinion
The product perfectly replaces the original part, after replacement the pump is tight. For this operation, it is worth buying a gasket and oring.
Review translated automatically
Reliable opinion
The clutch fits the cb 650sc model perfectly Clutch works very well on cold and warm engine I recommend
Review translated automatically
Reliable opinion
For my Hondas FT 500 (1983) & XBR 500 (1986) as spares. Remove the lever first, then punch out the old one from the contact pins side; it's an easy, light press fit. When pressing in the new one, align the hook on the switch with the notch in the clutch lever body. Note the hole in the switch also lines up with a hole at the underside of the alu body; it's for contact spray when needed. (Better use it before needed; once corroded the inner contact becomes difficult).
Review translated automatically
Reliable opinion
Affairs, it conducts electricity. However, it does not fit the 1976 GL1000 K1 model, as it has a larger diameter than the original (factory) and will not go into the hole in the handle holder. I had to take the original one apart despite the damage and was able to repair it. Perhaps this one will fit the specified GL1000 78-79 but I will check this when I give it to a colleague. It would be good to have the basic dimensions plotted on the parts in the photo to see if it will fit us.
Review translated automatically
Reliable opinion
A great copper washer for the oil drain bolt. Its main advantage is the right hardness. When tightening, it undergoes plastic deformation, so it perfectly fulfills its role - seals. Beware of washers made of copper alloys. Some of them are so hard that they do not yield even when hit with a hammer - they are not suitable for sealing the oil drain.
Review translated automatically
Reliable opinion
Some time ago I began to apply the principle of replacing copper washers at the time of oil change (previously I burned out). I must admit that for 1 zl it is not worth fighting with the old washer, especially since you will not get the same effect as with a new one. Now I treat the washer as a mandatory set - I always buy a set of oil + filter + drain bolt washer.
Review translated automatically
Reliable opinion
I bought this kit in the store with the information that it may not fit the cbr 250 but I made an aluminum ring on the wall 0.65mm height 0.80 mm circumference 30.00mm inner circumference 28.70 and it fits the rest of the dimensions is the same thank you for reliable information seller price in the service is 240 PLN and the ring cost me 10 PLN at a friend turner and everything is fine I recommend
Review translated automatically
Reliable opinion
My machines WSK M06B3 72r , Jawa 350 TS,Minsk 400, I have been sourcing parts from GMOTO for some time, I recommend because of the sufficient description of products, conformity of parts with the description, fast shipping, great contact. I am passionate about extinct motorcycles (demoluds to be precise), so I require a lot from the goods and here I find it,without unnecessary fuss.
Review translated automatically
Reliable opinion
Hello, I recently purchased some bearings shown in the ad. They were mounted to the scythe in the mtd tractor. SKF bearings have good strength and fit perfectly in the places for them. The advantage of the product is all kinds of uses, they perform well in any equipment. I recommend to purchase this product. Greetings
Review translated automatically
Reliable opinion
The product is very similar to the original. The only fault is that the threaded end is too short compared to the original. It's missing about 5 to 8 mm. This damaged the threads on my housing. I had to dismantle everything and redo the threading with ilsert.
Review translated automatically
Reliable opinion
When purchased, the bearing had no play, as befits a new bearing. The bearing has many uses. They can be mounted to wheels that are equipped with a drive on which a very high force acts. This bearing will 100% last more than a typical Chinese bearing.
Review translated automatically
Reliable opinion
YAMAHA XJR1300SP vintage 1999, all parts fit perfectly (to the eye does not differ from the original). The piston cover and brake piston grease are missing from the set, but the old cover was OK, it stayed, and I had the grease.
Review translated automatically
Reliable opinion
Everything ok full professionalism and fast delivery ( everything original) plus for remembering the motorcycle on the website and selecting parts by the selected version I will definitely use this store in the future I recommend it
Review translated automatically
Reliable opinion
Yamaha XVS 1300 CU year 2014 The bolt is shorter than the original and does not hold the size of the original bolt. It should not be indicated to fit this model. The only use for it is a copper gasket.
Review translated automatically
Reliable opinion
Honda GL500 from 1981.After intensive review of various sites, forums, I decided to buy this chain. The opinions of people who ride such motorcycles are unequivocal - DID.
Review translated automatically
Reliable opinion
Parts ok . Installed in Yamaha XT 660 X. However, it is also worth replacing the oil sealer which is not included in the set. Customer service super and shipping lightning fast.
Review translated automatically
Reliable opinion
I recommend, everything nicely, aesthetically packed,protected and as described. After installation everything as ok. recommend
Review translated automatically
Reliable opinion
Honda VFR 750 1995. I am satisfied with this kit, very easy installation especially since the gasket is already applied to the piston.
Review translated automatically
Reliable opinion
Perfect fit for 1987 honda CBR 1000 F received promptly and well packaged assembled and working properly.
Review translated automatically
Reliable opinion
Good quality, fit perfectly, arrived quickly and smoothly, satisfied, easy installation.
Review translated automatically
Reliable opinion