Forgot password
Order status
Free delivery from 150 euro
Manufacturer
Price
Sort
€2.80
CIRCLIP 20MM - CW20
€15.56
NEUTRAL SWITCH - 12-0072
Options +2 €51.84
Lowest price from 30 days before discount: €57.60
DID SCA0409ASV-118 closed timing chain
(10) 
Options +2 €51.84
Lowest price from 30 days before discount: €57.60
DID timing chain SCA0409ASV-118 open timing chain with lugs
(10) 
€37.07
Lowest price from 30 days before discount: €39.02
A set of TRW Lucas MES 336-7 metal clutch discs. - MES336-7
(1) 
€58.48
Lowest price from 30 days before discount: €61.56
TRW Lucas MCC 120-8 clutch disc set. - MCC120-8
€11.22
Lowest price from 30 days before discount: €11.81
Athena clutch cover gasket - S410210016014
(1) 
€9.22
Lowest price from 30 days before discount: €9.70
Athena valve cover gasket - S410210015007
(6) 
Browse by manufacturer
Products reviews
The screw is made with precision. I just pay attention to the assembly! The original screw is at least twice as long. The torque recommended in the service book (43Nm) is far too much for a Yamaha Thundercat, fekt is a broken thread.
Review translated automatically
Reliable opinion
For my Hondas FT 500 (1983) & XBR 500 (1986) as spares. Remove the lever first, then punch out the old one from the contact pins side; it's an easy, light press fit. When pressing in the new one, align the hook on the switch with the notch in the clutch lever body. Note the hole in the switch also lines up with a hole at the underside of the alu body; it's for contact spray when needed. (Better use it before needed; once corroded the inner contact becomes difficult).
Review translated automatically
Reliable opinion
Affairs, it conducts electricity. However, it does not fit the 1976 GL1000 K1 model, as it has a larger diameter than the original (factory) and will not go into the hole in the handle holder. I had to take the original one apart despite the damage and was able to repair it. Perhaps this one will fit the specified GL1000 78-79 but I will check this when I give it to a colleague. It would be good to have the basic dimensions plotted on the parts in the photo to see if it will fit us.
Review translated automatically
Reliable opinion
A great copper washer for the oil drain bolt. Its main advantage is the right hardness. When tightening, it undergoes plastic deformation, so it perfectly fulfills its role - seals. Beware of washers made of copper alloys. Some of them are so hard that they do not yield even when hit with a hammer - they are not suitable for sealing the oil drain.
Review translated automatically
Reliable opinion
Some time ago I began to apply the principle of replacing copper washers at the time of oil change (previously I burned out). I must admit that for 1 zl it is not worth fighting with the old washer, especially since you will not get the same effect as with a new one. Now I treat the washer as a mandatory set - I always buy a set of oil + filter + drain bolt washer.
Review translated automatically
Reliable opinion
The product is very similar to the original. The only fault is that the threaded end is too short compared to the original. It's missing about 5 to 8 mm. This damaged the threads on my housing. I had to dismantle everything and redo the threading with ilsert.
Review translated automatically
Reliable opinion
Everything ok full professionalism and fast delivery ( everything original) plus for remembering the motorcycle on the website and selecting parts by the selected version I will definitely use this store in the future I recommend it
Review translated automatically
Reliable opinion
Yamaha XVS 1300 CU year 2014 The bolt is shorter than the original and does not hold the size of the original bolt. It should not be indicated to fit this model. The only use for it is a copper gasket.
Review translated automatically
Reliable opinion
Everything was fine. The only thing I made a mistake. It is crankcase oil cap.and I wanted oil filler cap honda st 1100.fallo mio.no se si se podrá cambiar. Thanks
Review translated automatically
Reliable opinion
Perfect, my bike needed it, I hope it will last over time normally with did there should be no worries it remains a good value.
Review translated automatically
Reliable opinion
I recommend, everything nicely, aesthetically packed,protected and as described. After installation everything as ok. recommend
Review translated automatically
Reliable opinion
It just fit perfectly on my Honda FT500. Gave it a little oil first, it didn't take much for the flywheel to come off.
Review translated automatically
Reliable opinion
Exactly the same as the original, the order has arrived in the estimated time and the quality of the material seems to be correct.
Review translated automatically
Reliable opinion
Fits perfectly. Always happy to return. Good and inexpensive. Do what you are supposed to do - seal. MFG Ulrich Schulzke
Review translated automatically
Reliable opinion
Fast delivery, excellent quality! Sterilely packed and clean, exactly the same as in the picture! The quality shows
Review translated automatically
Reliable opinion
Honda HRV 750 Africa twin rd04 - fits without any problem, installation very efficient, goods as expected.
Review translated automatically
Reliable opinion
Good quality, good fit for the selected motorcycle, good aesthetics and material quality good price.
Review translated automatically
Reliable opinion
XRV 750 rd04, everything is fine, the gasket fits perfectly, it is soft. I can confidently recommend shopping here.
Review translated automatically
Reliable opinion
Honda XL600V Transalp '96 - First Class Goods
Review translated automatically
Reliable opinion