Forgot password
Order status
Free delivery from 150 euro
Motorcycle ignition system
Romet Kadet 50
Manufacturer
Price
Sort
Browse by manufacturer
Products reviews
Romet Kadet, the interrupter looks good at first glance, however, you need to work on it so that there are no problems with it. First of all, tighten the locking plate on the side and strike the rivet which holds the part isolated from the base in one place (in my case it worked on this rivet and caused short circuits). The second thing is to bend the spring from the toothbrush like the original so that it does not go into the holes, but falls into a certain place locking on them (U-bend where it enters the hole). Adjust the curvature of the anvil to the toothbrush by appropriate bending (in my case it went that oblique). And the last thing is to throw away those plastic insulating washers and buy thin ones made of rezotex or ebonite ) to match the height of these washers to the anvil.
Review translated automatically
Reliable opinion
I own Motorynka Romet Pony M-2 Motorcycle.The capacity of the engine is 49.8 cm, and the year of production is 1980.The product made in very good quality, I recommend to all buyers. I have already ordered Motorcycle parts from this store a couple of times, and not only for Motorynka, but for other Motorcycles too.I think that's enough, the products from this store I rate 100%.There were no delays with the shipment, or any complications, I recommend to all buyers!
Review translated automatically
Reliable opinion
The interrupter has a German TUV certificate, this is always a guarantee of quality. After installation and ignition alignment, it works as Predom Romet factory ordered. During installation I had a problem with the pin on which the interrupter is seated (I detected a small play, meanwhile it should not be there, the pin should be mounted at a right angle of 90 degrees, a little tinkering threading and the problem eliminated). Romet Ogar 205, year of manufacture 1987.
Review translated automatically
Reliable opinion
Romet Kadet , the capacitor fits in place of the old one without reservation, the installation went without a problem. Wire minimally shorter than the original about 3mm, but reaches the same with the same arrangement in the spark gap. Remember during installation to soak the felt in oil and properly bend it to adhere to the magnet cam (if you install without bending it will not lubricate).
Review translated automatically
Reliable opinion
Romet Ogar 205 from 1990.I received this smaller capacitor with a length of 22 mm , it has a shorter wire and there was a problem with connecting it to the coil.After talking to the store staff I was immediately sent the longer capacitor -27 mm without any additional cost.This capacitor has a wire 5 mm longer and fits perfectly to the above type of Romet. I recommend this store.
Review translated automatically
Reliable opinion
A capacitor is an important component in an electrical system. It is really worth replacing from time to time preventively. Fits into a rometa ogar 205, a little work to put on (pulling off the cover, magneto, etc.), but there were no problems with fitting into the spark gap. After installation, the whole installation works well. Romet Ogar 205, year of manufacture 1987
Review translated automatically
Reliable opinion
Romet Kadet 87. Does not fit in the original base. Too large diameter of locating pins. A failure! Execution poor. Spacing of screws-fits. Cables very thin. Not a Polish manufacturer as I was assured. Goods to return. I do not recommend this coil, avoid from afar!
Review translated automatically
Reliable opinion
Romet Kadet 87. Fits in place of the original ignition base. No need to saw anything. Insulating washers- a failure, too small diameter of the hole and too high. Isolating washer at the point of contact of the anvil spring, badly mounted, placed by which can contact.
Review translated automatically
Reliable opinion
For the mosquito 2350 with the s38 engine (egg), the coil purchased does not fit in the holes of the spark arrestor (the spacing of the pins is wider by about 0.5mm, which makes it impossible to install without interference from a file). As for the materials, I have no major complaints, however, the wire could be a little longer.
Review translated automatically
Reliable opinion
Mr2375, Ogar 205 and 50-T1 toners. This coil will recall the ignition of any of them in the 2375 has worked for 5 years and I have no complaints. It always required a slight grinding, but that's a minor thing. The best part is that the spark would kill a horse and until you hear it crackle beautifully.
Review translated automatically
Reliable opinion
Mosquito Mosquito s38 1975-purchased parts are of high quality in terms of workmanship, aesthetics, efficiency of operation -I recommend many motorcycles I assemble and with this company super to cooperate-mega efficient shipping 24 hours to the other end of the Polish b.good contact with the seller.RECOMMENDED
Review translated automatically
Reliable opinion
Romet Ogar 205 The ignition coil is a tragedy. It does not fit in the mounting holes. After reaming the holes and installing the coil, it was impossible to put on the magnet wheel. It was necessary to file the coil. Final mounted worked 50 seconds and died.
Review translated automatically
Reliable opinion
Motorcycle 50 ccm 1986 year of production, the base of the ignition switch was quite "defeated". Years of use have done their part and it was necessary to transfer the electrical and ignition equipment to a new base .Now it is possible to smoothly regulate the ignition.
Review translated automatically
Reliable opinion
The interrupter is carefully made with attention to detail, fits very well on the pin in the spark gap. There is no excessive play and after proper adjustment the platinum contact is all over the surface. A product worth recommending!
Review translated automatically
Reliable opinion
I have a rometa T1. 83r. Purchased capacitor is the same parameters as in the original.Mounting identical was no problem with installation After firing and driving a few kilometers romecik works correctly.
Review translated automatically
Reliable opinion
Motorcycle I bought 2 capacitors the first was enough for an hour of driving and burned up during the ride on a hot day and push home The second one has been working for quite a long time and is ok so it all depends on the exemplar.
Review translated automatically
Reliable opinion
Super product, when ordering I wrote in the additional information that I wanted a 27mm capacitor and such came. Easy to install because it is exactly like the original. The motorcycle starts, drives properly.
Review translated automatically
Reliable opinion
Romet Motorynka 1980 Motorynka undergoes a major overhaul, I replace all components that are damaged or tired of time :). Good quality goods. Was it worth buying - definitely YES
Review translated automatically
Reliable opinion
Romet Motorynka 1980 Motorynka undergoes a major overhaul, I replace all components that are damaged or tired of time :). Good quality goods. Was it worth buying - definitely YES
Review translated automatically
Reliable opinion
The capacitor could have a slightly longer conductor because it is missing after carrying out like the original and the dimpled mount is too low, when put on, the wire is very close to the magnet.
Review translated automatically
Reliable opinion
Romet ogar 205 50cm.coil as best as possible,good quality,but it does not fit on the centering sleeve,too large diameter you need to drill holes,otherwise everything is as described.I recommend
Review translated automatically
Reliable opinion
It lasted only one day motorcycle then began to shoot and have no power after changing to another capacitor came to life did not come what is in the picture another bubble to the collection
Review translated automatically
Reliable opinion
Hello Romet ogar 205.There was no spark match after putting this capacitor the spark came back and I can be happy that my ogar rides. Workmanship is good. Well that works and recommend
Review translated automatically
Reliable opinion
Romet Ogar 205 vintage 1987 Product 100% as described sensational quality of workmanship I highly recommend this seller professional approach to the customer
Review translated automatically
Reliable opinion
komar 2320/engine s38. Everything works great, good quality, I highly recommend. Have an old motorcycle, want to rebuild it on good parts? Only Gmotot
Review translated automatically
Reliable opinion
condenser for a colleague, but he bought 3 pieces at our local store and 3 were hit .;/ and here it is not only cheaper, but also the fire started from a kick xD
Review translated automatically
Reliable opinion
I bought this coil with rather mixed feelings. When it arrived it made a very good first impression. 0 problems with installation and the moped finally came to life
Review translated automatically
Reliable opinion
romet ogar 205 1987 year. good quality strong spark burns on shot I ordered it because mine was zabryczny and the old motorcycle almost did not start I highly recommend !
Review translated automatically
Reliable opinion
Romet mr 2375 what to talk about.Coil for the spark gap fits however, you need to slightly "fit" it with a file because otherwise it rubs against the magneto.Romet fires up and rides.
Review translated automatically
Reliable opinion
Romet komar, the coil fits on the old holes, however, I had to grind it to enter the magneto (old), but the coil does its job. I recommend
Review translated automatically
Reliable opinion
Another thing that is worth having in your spare equipment. The cost of a few zlotys, very good quality and workmanship, and above all, the holy peace of mind
Review translated automatically
Reliable opinion
I am the owner of a Romet - Komar from the year 1970.The capacitor I bought during the installation fit like the original, it works just as well. I recommend.
Review translated automatically
Reliable opinion
I bought the part for a romet pony motorcycle and it performs very well and is durable. Fast shipping on the second day. I recommend this seller
Review translated automatically
Reliable opinion
Poor quality, does not fit the original spark arrestor base, you have to redo the housing, it is too wide and the pin spacing does not fit.
Review translated automatically
Reliable opinion
Romet Kadet 87. Quality and workmanship does not differ from the original. The cable of ideal length. The overlap, everything fits. I recommend
Review translated automatically
Reliable opinion
Great workmanship, fits motorcycle, delivery as much as possible on + Everything in order, (not everyone may fit the length of the cable)
Review translated automatically
Reliable opinion
Romet Kadet year prod. 1983 capacitor fits perfectly into the original base of the spark gap, 100% fulfills its role RECOMMENDED
Review translated automatically
Reliable opinion
Capacitor made very well, cable length just right to run it through the stator. Works 100% recommend
Review translated automatically
Reliable opinion
Romet pony 80r fits on the mounting holes but the threads are embedded in glue and when tightening the pony began to rotate.
Review translated automatically
Reliable opinion
When repairing a Romet ogar 205 it is worth checking and preferably replacing because it can make a lot of difference, in my case it works and is ok
Review translated automatically
Reliable opinion