Motorcycle parts
Honda GL 1500 Goldwing 1990 - Page 5

2018-11-01, 20:15

View original

Krzysztof

I ordered the air vents with the motorcycle Honda XRV 750 Africa Twin - 1999 in mind. They fit the front calipers as well as the rear caliper. After screwing in, there is a little bit of thread sticking out(this is for a small minus), which is covered by a blanking rubber. They successfully replace the original, which is twice as expensive in the service. To the aesthetics and solidity rather can not be complained about - no burrs, the layer of zinc is placed on well-prepared steel. When tightening, care should be taken to select a perfectly matching wrench, scratches and destruction of the zinc layer can result in the appearance of rust in a fairly short time due to the fact that the material is steel. The downgrade for the material is due to the fact that I would prefer stainless steel instead of steel and zinc.

Review translated automatically

Reliable opinion

2020-06-22, 13:07

View original

Stanisław

The whole kit fits perfectly. I recommend to regenerate the baked clutch. Previously it was impossible to move it, now it goes in with fingers without any problems.

Review translated automatically

Reliable opinion

2021-10-08, 12:10

View original

Artur

There is nothing to say about Hiflo and the quality of their products, so I usually choose their filters.

Review translated automatically

Reliable opinion

2021-06-29, 10:25

View original

Leszek

Honda XL 600 V Transalp. A filter like a filter, it's hard to judge it by eye. It screwed in easily and pleasantly. All indications are that it filters as God has commanded. Shouldn't there be an o-ring in the place where it is screwed onto the spigot protruding from the block? I can't hide the fact that I would be happy to win four hundred bucks because I need a clutch and cash is tight.

Review translated automatically

Reliable opinion

2020-05-03, 00:23

View original

Maciej

Wsk 125 The frame is nice, you can't expect more from a plastic metallized one. It fits my wsk-i nicely. The only big minus is that it did not fit completely in the holes - I had to widen the holes with a drill both at the top and bottom. Other than that, installation was easy. I recommend the product for those who don't mind making up holes.

Review translated automatically

Reliable opinion

2020-03-30, 20:41

View original

Michał

Sealers without complaint. In a rigid and secure package a set of sealers and covers for two leaguers. Assembly trivially easy (for those who like and have an idea of DIY and small repairs). The fit is perfect. So far zero problem and the lags work perfectly in combination with Motul 10W oil.

Review translated automatically

Reliable opinion

2021-05-08, 07:38

View original

Andrzej

Plastic license plate frame looks like a good chrome material I changed the plate because I became the owner of a Suzuki Intruder VL 125 2000 year all in all. Looks super material fine that's why the price very low ugly comes longer.

Review translated automatically

Reliable opinion

2020-07-08, 19:23

View original

Waldemar

My machine is an 86 Honda Shadow VT 1100 . Purchased parts were not dedicated for this vintage , so as a novice user I bought blind and surprisingly they fit . Installation was no problem and the material and workmanship flawless . G Moto and product on pistket . LWG .

Review translated automatically

Reliable opinion

2017-05-15, 22:44

View original

Maciej

Patient Honda CB600F Hornet, vintage 2001, non-functioning fan switch. What can I say, a top-notch product. After replacement, the fan spins and works at its best. This radiator fan switch is a great product, I would recommend it to anyone

Review translated automatically

Reliable opinion

2025-01-26, 09:45

View original

Pedro

It fits perfectly, on and working. It took ten days to arrive more or less, but the important thing is that the part is fully compatible despite the age of the bike. Vfr 750 f from year 91, in 34 years the first part that breaks.

Review translated automatically

Reliable opinion

2020-10-06, 06:56

View original

Mateusz

The gasket of very good quality fits my model perfectly. part of the exhaust no longer comes out sideways so that the sound of the exhaust system work and the correctness of operation is very good. Thank you and recommend

Review translated automatically

Reliable opinion

2019-04-09, 08:40

View original

Rafał

I purchased the bearings with seals a few days ago for my Honda cbr 1000 f sc 21 motorcycle. The parts came to me in no time. At the moment they are waiting for installation because I have to wait until the wheel returns from painting

Review translated automatically

Reliable opinion

2019-06-17, 07:58

View original

Damian

In the category of quality/price very nice frame. Strong plastic imitating chrome. Aesthetics at a high level. Lightweight and durable And the license plate enters on contact ( for me a plus because there is no slack). I recommend

Review translated automatically

Reliable opinion

2018-11-23, 07:39

View original

Łukasz

The biggest minus for the shipping time. Zero information about the extension of the shipping time due to the lack of product ( one was for the other they waited for delivery)and I waited 5 days for the package by courier. Product ok.

Review translated automatically

Reliable opinion

2021-01-24, 16:53

View original

Bogdan

I own a motorcycle honda CBR 1000F, vintage 1966, capacity 1000 cm. This is another filter from this manufacturer that I bought, and I have never had any problems with them have always served their purpose.

Review translated automatically

Reliable opinion

2022-01-11, 15:35

View original

Wojciech

XL 600VA 1987 Oil easy to use does not require instructions. I recommend this product. Very good quality product for its price. Quick delivery hassle-free service. I recommend

Review translated automatically

Reliable opinion

2025-09-02, 18:25

View original

Tomáš

The above set of seals for front forks Honda Deauville NT 700 V, r.v. 2008 absolutely fine, trouble-free assembly, the product suits the type of moto, appears to be of good quality.

Review translated automatically

Reliable opinion

2025-03-01, 08:08

View original

HOCMERT

20/20 The product corresponds to 100% of my expectations, my entire order was carefully packaged and delivery was very fast. You can order with your eyes closed.

Review translated automatically

Reliable opinion

2020-03-30, 20:44

View original

Michał

The protections, compared to the old ones, are slightly wider, more rigid and more "expandable", which makes them fit perfectly into the groove in the lade blocking the sealers.

Review translated automatically

Reliable opinion

2025-07-15, 05:30

View original

KARLOS

Same as the original, but 75% cheaper. Quick response to e-mails. Although with a little more delay in delivery with respect to what was said on the page.

Review translated automatically

Reliable opinion

2017-09-04, 10:25

View original

Mariusz

frame very nice, put on jawa ts 350 looks very good on this motorcycle, installation also very pleasant immediately changes the name of the motorcycle adds better charm

Review translated automatically

Reliable opinion

2024-09-25, 05:27

View original

Filip

Very good solution for those who want to replace the license plate frame with a new one. The price is very affordable. The quality of workmanship is also flawless. I can recommend

Review translated automatically

Reliable opinion

2020-08-08, 13:12

View original

Rajmund

The motorcycle is a honda transalp 600 1996r.The element fit perfectly without any reservations thanks to good workmanship and fit the repair went quickly and efficiently.Regards

Review translated automatically

Reliable opinion

2024-09-24, 06:41

View original

Tomasz

The filter performs its function perfectly, after pouring off the old oil you can not see any flecks, etc. Thanks to the flexible gasket, I tighten it by hand and nothing leaks.

Review translated automatically

Reliable opinion

2024-11-08, 06:13

View original

Milan

Good quality, good price, fast delivery. Very few sellers for this product and none at this price. Maximum satisfaction. I will order again. This time turn signals.

Review translated automatically

Reliable opinion

2020-03-15, 20:37

View original

Sławomir

Honda Transalp XL V600. The pistons arrived armor-packed. The store assured that they would fit and of course they did, brakes like new. I sincerely recommend.

Review translated automatically

Reliable opinion

2021-12-12, 20:14

View original

Kordian

I always buy filters from HIflo and this time, too, everything fits until nice. I recommend to trust this brand as much as possible. Gmoto as usual at a high level. XJ600

Review translated automatically

Reliable opinion

2024-05-03, 07:48

View original

Bogusław

Great sealers, they fit nice and tight even though the lag was polished, so far only about 100km after replacement but no drop on the lag, I recommend

Review translated automatically

Reliable opinion

2025-04-13, 11:27

View original

NIKOS

Excellent product. It fit properly in the caliper and I no longer have any leakage from the wear and tear of the previous one. Tourmax quality comparable to the factory ones.

Review translated automatically

Reliable opinion

2025-05-08, 15:14

View original

lespilette

top received on time, perfect service, well packaged, no problem for transport.....good quality product for my Xjr, same as in France

Review translated automatically

Reliable opinion

2019-08-26, 12:15

View original

Sławomir

I own a Honda NT650V Deauville. The seals seem solid because of the 2 spring rings. The previous ones only had one such ring.

Review translated automatically

Reliable opinion

2025-07-22, 11:06

View original

Stefanos

On CBF 500A applied correctly to the radiator and it works just like the factory switch. It also seals as it should and there are no leaks.

Review translated automatically

Reliable opinion

2025-08-07, 09:58

View original

Vincent

Parts corresponding to the original start at a slightly lower temperature 85/90 degrees original start at 100 degrees aesthetics equal to the original

Review translated automatically

Reliable opinion

2021-08-13, 09:01

View original

Krzysztof

It works 100% pity only that the kit does not include a copper washer. To seal the connection. Other than that, the product is of good quality. I really recommend

Review translated automatically

Reliable opinion

2018-03-18, 08:22

View original

Jarosław

Suzuki Intruder 800, seals of good quality, all dimensions met, has been installing for years in various motorcycles, certainly not the last :)

Review translated automatically

Reliable opinion

2020-04-26, 21:15

View original

Marcin

Fits perfectly on my old venerable XJtek, from 96. No problems with threads or leakage from under the filter gasket. I highly recommend the product.

Review translated automatically

Reliable opinion

2025-06-17, 11:40

View original

Thomas

It fits and is tight so far! Unfortunately, I can't say any more about this, as it will only become clear at the next oil change/oil filter replacement

Review translated automatically

Reliable opinion

2025-09-18, 10:04

View original

ΔΗΜΗΤΡΗΣ

It has nickel finish but its plastic, the article says metallic but thats wrong, if you want it for enduro bike or adv its not metallic

Review translated automatically

Reliable opinion

2016-05-27, 06:41

View original

Andrzej

-Kawasaki Vulcan EN 500A 1991. -after installation, the tightness of the exhaust system improved -It was definitely worth to buy the above mentioned product.

Review translated automatically

Reliable opinion

2023-05-24, 07:13

View original

Remi

Sealers well made, there was no problem with the installation which indicates well-behaved parameters. Tight, oil no longer leaks.

Review translated automatically

Reliable opinion