Motorcycle engine - parts
Derbi Mulhacen 660 Cafe 2010

2020-07-30, 12:06

View original

Darek

The screw is made with precision. I just pay attention to the assembly! The original screw is at least twice as long. The torque recommended in the service book (43Nm) is far too much for a Yamaha Thundercat, fekt is a broken thread.

Review translated automatically

Reliable opinion

2020-04-12, 13:22

View original

Piotr

The product perfectly replaces the original part, after replacement the pump is tight. For this operation, it is worth buying a gasket and oring.

Review translated automatically

Reliable opinion

2025-05-26, 19:33

View original

Zbib

Beautiful, I recommend it... ...

Review translated automatically

Reliable opinion

2023-05-24, 10:46

View original

Dawid

A great copper washer for the oil drain bolt. Its main advantage is the right hardness. When tightening, it undergoes plastic deformation, so it perfectly fulfills its role - seals. Beware of washers made of copper alloys. Some of them are so hard that they do not yield even when hit with a hammer - they are not suitable for sealing the oil drain.

Review translated automatically

Reliable opinion

2021-02-07, 13:11

View original

RDS

Some time ago I began to apply the principle of replacing copper washers at the time of oil change (previously I burned out). I must admit that for 1 zl it is not worth fighting with the old washer, especially since you will not get the same effect as with a new one. Now I treat the washer as a mandatory set - I always buy a set of oil + filter + drain bolt washer.

Review translated automatically

Reliable opinion

2016-09-09, 10:49

View original

Rafał

I bought this kit in the store with the information that it may not fit the cbr 250 but I made an aluminum ring on the wall 0.65mm height 0.80 mm circumference 30.00mm inner circumference 28.70 and it fits the rest of the dimensions is the same thank you for reliable information seller price in the service is 240 PLN and the ring cost me 10 PLN at a friend turner and everything is fine I recommend

Review translated automatically

Reliable opinion

2024-12-05, 18:18

View original

ΑΝΔΡΕΑΣ

Thank you for shipping the correct parts that I ordered for my motorcycle.Everything was delivered in the best condition possible.Im very pleased with your team and management.The shipment was very fast and very cheap.All the parts were suitable and they were exactly what I ordered.Thank you a million.Andreas from Greece

Review translated automatically

Reliable opinion

2021-02-05, 07:32

View original

Marek

Hello, I recently purchased some bearings shown in the ad. They were mounted to the scythe in the mtd tractor. SKF bearings have good strength and fit perfectly in the places for them. The advantage of the product is all kinds of uses, they perform well in any equipment. I recommend to purchase this product. Greetings

Review translated automatically

Reliable opinion

2024-09-19, 08:55

View original

BOULET-DESBAREAU

The product is very similar to the original. The only fault is that the threaded end is too short compared to the original. It's missing about 5 to 8 mm. This damaged the threads on my housing. I had to dismantle everything and redo the threading with ilsert.

Review translated automatically

Reliable opinion

2020-08-18, 22:09

View original

Jakub

When purchased, the bearing had no play, as befits a new bearing. The bearing has many uses. They can be mounted to wheels that are equipped with a drive on which a very high force acts. This bearing will 100% last more than a typical Chinese bearing.

Review translated automatically

Reliable opinion

2023-08-18, 11:07

View original

Artur

Everything ok full professionalism and fast delivery ( everything original) plus for remembering the motorcycle on the website and selecting parts by the selected version I will definitely use this store in the future I recommend it

Review translated automatically

Reliable opinion

2020-11-22, 15:13

View original

Jacek

Yamaha XVS 1300 CU year 2014 The bolt is shorter than the original and does not hold the size of the original bolt. It should not be indicated to fit this model. The only use for it is a copper gasket.

Review translated automatically

Reliable opinion

2023-07-28, 07:41

View original

Adam

Parts ok . Installed in Yamaha XT 660 X. However, it is also worth replacing the oil sealer which is not included in the set. Customer service super and shipping lightning fast.

Review translated automatically

Reliable opinion