Forgot password
Order status
Free delivery from 150 euro
Motorcycle engine - parts
Honda CB 400 T 1978
Manufacturer
Price
Sort
€21.51
FLYWHEEL PULLER - 08-0086
Options +2 €68.64
Lowest price from 30 days before discount: €76.26
DID timing chain SCA0412ASV-110 open timing chain with lugs
(6) 
€10.26
Lowest price from 30 days before discount: €10.80
TRW Lucas MEF 147-4 clutch springs - MEF147-4
€15.56
6304 SKF bearing
€33.03
Lowest price from 30 days before discount: €34.77
A set of TRW Lucas MES 326-6 metal clutch discs. - MES326-6
(1) 
€4.94
Lowest price from 30 days before discount: €5.20
Athena alternator cover gasket - S410210017005
(1) 
€10.57
Lowest price from 30 days before discount: €11.13
Athena clutch cover gasket - S410210008123
(1) 
€13.48
Lowest price from 30 days before discount: €14.19
Athena valve cover gasket - S410210015021
(1) 
Browse by manufacturer
Products reviews
The screw is made with precision. I just pay attention to the assembly! The original screw is at least twice as long. The torque recommended in the service book (43Nm) is far too much for a Yamaha Thundercat, fekt is a broken thread.
Review translated automatically
Reliable opinion
Honda CB 400N 1983 Product very well made , high quality of material used and precise machining . I recommend replacing the o-ring every time you change the filter
Review translated automatically
Reliable opinion
For my Hondas FT 500 (1983) & XBR 500 (1986) as spares. Remove the lever first, then punch out the old one from the contact pins side; it's an easy, light press fit. When pressing in the new one, align the hook on the switch with the notch in the clutch lever body. Note the hole in the switch also lines up with a hole at the underside of the alu body; it's for contact spray when needed. (Better use it before needed; once corroded the inner contact becomes difficult).
Review translated automatically
Reliable opinion
Affairs, it conducts electricity. However, it does not fit the 1976 GL1000 K1 model, as it has a larger diameter than the original (factory) and will not go into the hole in the handle holder. I had to take the original one apart despite the damage and was able to repair it. Perhaps this one will fit the specified GL1000 78-79 but I will check this when I give it to a colleague. It would be good to have the basic dimensions plotted on the parts in the photo to see if it will fit us.
Review translated automatically
Reliable opinion
The product is very similar to the original. The only fault is that the threaded end is too short compared to the original. It's missing about 5 to 8 mm. This damaged the threads on my housing. I had to dismantle everything and redo the threading with ilsert.
Review translated automatically
Reliable opinion
Unfortunately it does not fit the Honda CB 450s motorcycle. Not the right size (I was buying a little by feel after the dimensions from the Honda catalog). Fortunately, I had the correct size at my place. Other than that, the aluminum washer without reservation. Greetings
Review translated automatically
Reliable opinion
Yamaha XVS 1300 CU year 2014 The bolt is shorter than the original and does not hold the size of the original bolt. It should not be indicated to fit this model. The only use for it is a copper gasket.
Review translated automatically
Reliable opinion
I recommend, everything nicely, aesthetically packed,protected and as described. After installation everything as ok. recommend
Review translated automatically
Reliable opinion
Fast delivery, excellent quality! Sterilely packed and clean, exactly the same as in the picture! The quality shows
Review translated automatically
Reliable opinion
The chain made very aesthetically pleasing all dimensions in accordance with the original without any problems fit the gears.
Review translated automatically
Reliable opinion
Honda CB 400 N year 1985, fits nicely nothing leaks :)
Review translated automatically
Reliable opinion