Forgot password
Order status
Free delivery from 150 euro
Motorcycle engine - parts
Honda CB-X4 1300 DC 1998
Manufacturer
Price
Sort
Options +4 
€4.71
Lowest price from 30 days before discount: €4.96
Athena Honda SH 300 07-14 CRF 110F 13-20 valve cover bolt gasket OEM: 90401KWWC00; 90543MV9670 - S410210015128
(2) 
€2.96
Lowest price from 30 days before discount: €3.12
Athena O-Ring 2x82 mm water pump gasket - M752008200004
€48.34
Lowest price from 30 days before discount: €50.88
A set of TRW Lucas MES 335-9 metal clutch discs. - MES335-9
€7.86
Lowest price from 30 days before discount: €8.28
Athena clutch cover gasket - S410210008017
(2) 
€9.22
Lowest price from 30 days before discount: €9.70
Athena valve cover gasket - S410210015007
(6) 
€13.07
JMT Honda clutch sensor
Browse by manufacturer
Products reviews
I recommend the clutch pump repair kit from Tourmax. Replacement is trivially easy, and all the necessary things that wear out in such a pump are included in the set. For a small amount of money, you can easily recondition a malfunctioning pump and eliminate clutch problems.
Review translated automatically
Reliable opinion
The screw is made with precision. I just pay attention to the assembly! The original screw is at least twice as long. The torque recommended in the service book (43Nm) is far too much for a Yamaha Thundercat, fekt is a broken thread.
Review translated automatically
Reliable opinion
The whole kit fits perfectly. I recommend to regenerate the baked clutch. Previously it was impossible to move it, now it goes in with fingers without any problems.
Review translated automatically
Reliable opinion
For my Hondas FT 500 (1983) & XBR 500 (1986) as spares. Remove the lever first, then punch out the old one from the contact pins side; it's an easy, light press fit. When pressing in the new one, align the hook on the switch with the notch in the clutch lever body. Note the hole in the switch also lines up with a hole at the underside of the alu body; it's for contact spray when needed. (Better use it before needed; once corroded the inner contact becomes difficult).
Review translated automatically
Reliable opinion
Affairs, it conducts electricity. However, it does not fit the 1976 GL1000 K1 model, as it has a larger diameter than the original (factory) and will not go into the hole in the handle holder. I had to take the original one apart despite the damage and was able to repair it. Perhaps this one will fit the specified GL1000 78-79 but I will check this when I give it to a colleague. It would be good to have the basic dimensions plotted on the parts in the photo to see if it will fit us.
Review translated automatically
Reliable opinion
A great copper washer for the oil drain bolt. Its main advantage is the right hardness. When tightening, it undergoes plastic deformation, so it perfectly fulfills its role - seals. Beware of washers made of copper alloys. Some of them are so hard that they do not yield even when hit with a hammer - they are not suitable for sealing the oil drain.
Review translated automatically
Reliable opinion
Some time ago I began to apply the principle of replacing copper washers at the time of oil change (previously I burned out). I must admit that for 1 zl it is not worth fighting with the old washer, especially since you will not get the same effect as with a new one. Now I treat the washer as a mandatory set - I always buy a set of oil + filter + drain bolt washer.
Review translated automatically
Reliable opinion
Hello, I recently purchased some bearings shown in the ad. They were mounted to the scythe in the mtd tractor. SKF bearings have good strength and fit perfectly in the places for them. The advantage of the product is all kinds of uses, they perform well in any equipment. I recommend to purchase this product. Greetings
Review translated automatically
Reliable opinion
Have used these gaskets for the valve cover screws and they do exactly what they are supposed to. They seal tight, keep oil in and seem like a definite improvement over worn original gaskets. Installation was easy and the material feels both resilient and durable. No signs of oil sweat after installation - completely satisfied!
Review translated automatically
Reliable opinion
The product is very similar to the original. The only fault is that the threaded end is too short compared to the original. It's missing about 5 to 8 mm. This damaged the threads on my housing. I had to dismantle everything and redo the threading with ilsert.
Review translated automatically
Reliable opinion
When purchased, the bearing had no play, as befits a new bearing. The bearing has many uses. They can be mounted to wheels that are equipped with a drive on which a very high force acts. This bearing will 100% last more than a typical Chinese bearing.
Review translated automatically
Reliable opinion
It fits perfectly, on and working. It took ten days to arrive more or less, but the important thing is that the part is fully compatible despite the age of the bike. Vfr 750 f from year 91, in 34 years the first part that breaks.
Review translated automatically
Reliable opinion
Unfortunately it does not fit the Honda CB 450s motorcycle. Not the right size (I was buying a little by feel after the dimensions from the Honda catalog). Fortunately, I had the correct size at my place. Other than that, the aluminum washer without reservation. Greetings
Review translated automatically
Reliable opinion
It works correctly and was very easy to install. My bike is a 2006 CBF600N and I had no problems at all, it only takes a socket wrench and needle nose pliers to remove and attach the connecting cable.
Review translated automatically
Reliable opinion
Everything ok full professionalism and fast delivery ( everything original) plus for remembering the motorcycle on the website and selecting parts by the selected version I will definitely use this store in the future I recommend it
Review translated automatically
Reliable opinion
Yamaha XVS 1300 CU year 2014 The bolt is shorter than the original and does not hold the size of the original bolt. It should not be indicated to fit this model. The only use for it is a copper gasket.
Review translated automatically
Reliable opinion
I own a 2005 Honda CBF600. The sensor fit without a problem, plug and play. The replacement took 5 minutes. Fulfillment of the order was lightning fast, the product was with me the next day. Highly recommend.
Review translated automatically
Reliable opinion
Honda VFR 750 1995. I am satisfied with this kit, very easy installation especially since the gasket is already applied to the piston.
Review translated automatically
Reliable opinion
Fast service. Good place to shop and at a really good price. They ship fast. It's not the last time I shop there.
Review translated automatically
Reliable opinion
Exactly the same as the original, the order has arrived in the estimated time and the quality of the material seems to be correct.
Review translated automatically
Reliable opinion
Perfect fit for 1987 honda CBR 1000 F received promptly and well packaged assembled and working properly.
Review translated automatically
Reliable opinion
Fast delivery, excellent quality! Sterilely packed and clean, exactly the same as in the picture! The quality shows
Review translated automatically
Reliable opinion
very good suitability.
Review translated automatically
Reliable opinion
clutch cover gasket of very good quality, perfect for motorcycle honda cbr 1000 f of 1987 in reconstruction greetings
Review translated automatically
Reliable opinion
Good quality, fit perfectly, arrived quickly and smoothly, satisfied, easy installation.
Review translated automatically
Reliable opinion
Good quality, good fit for the selected motorcycle, good aesthetics and material quality good price.
Review translated automatically
Reliable opinion
XRV 750 rd04, everything is fine, the gasket fits perfectly, it is soft. I can confidently recommend shopping here.
Review translated automatically
Reliable opinion