Motorcycle engine - parts
Honda CBF 500 2007

2020-07-30, 12:06

View original

Darek

The screw is made with precision. I just pay attention to the assembly! The original screw is at least twice as long. The torque recommended in the service book (43Nm) is far too much for a Yamaha Thundercat, fekt is a broken thread.

Review translated automatically

Reliable opinion

2019-01-12, 09:03

View original

Andrzej

Honda Cbf 500 2007. Sealers very good quality . Hassle-free installation. You can see at a glance that it is an original product of Athena.Oil burning I have already.I recommend.

Review translated automatically

Reliable opinion

2020-02-25, 22:48

View original

Johan

For my Hondas FT 500 (1983) & XBR 500 (1986) as spares. Remove the lever first, then punch out the old one from the contact pins side; it's an easy, light press fit. When pressing in the new one, align the hook on the switch with the notch in the clutch lever body. Note the hole in the switch also lines up with a hole at the underside of the alu body; it's for contact spray when needed. (Better use it before needed; once corroded the inner contact becomes difficult).

Review translated automatically

Reliable opinion

2024-03-04, 06:42

View original

Łukasz

Affairs, it conducts electricity. However, it does not fit the 1976 GL1000 K1 model, as it has a larger diameter than the original (factory) and will not go into the hole in the handle holder. I had to take the original one apart despite the damage and was able to repair it. Perhaps this one will fit the specified GL1000 78-79 but I will check this when I give it to a colleague. It would be good to have the basic dimensions plotted on the parts in the photo to see if it will fit us.

Review translated automatically

Reliable opinion

2021-02-05, 07:32

View original

Marek

Hello, I recently purchased some bearings shown in the ad. They were mounted to the scythe in the mtd tractor. SKF bearings have good strength and fit perfectly in the places for them. The advantage of the product is all kinds of uses, they perform well in any equipment. I recommend to purchase this product. Greetings

Review translated automatically

Reliable opinion

2025-08-03, 20:59

View original

Aksel

Have used these gaskets for the valve cover screws and they do exactly what they are supposed to. They seal tight, keep oil in and seem like a definite improvement over worn original gaskets. Installation was easy and the material feels both resilient and durable. No signs of oil sweat after installation - completely satisfied!

Review translated automatically

Reliable opinion

2024-09-19, 08:55

View original

BOULET-DESBAREAU

The product is very similar to the original. The only fault is that the threaded end is too short compared to the original. It's missing about 5 to 8 mm. This damaged the threads on my housing. I had to dismantle everything and redo the threading with ilsert.

Review translated automatically

Reliable opinion

2017-07-11, 09:59

View original

Mariusz

I am a happy owner of a yamaha yzf 125r in which I recently noticed oil loss , I replaced the valve seals which I ordered from gmoto and I am very satisfied , solidly made . Easy to install and fit to my 2010r modelj recommend to everyone.

Review translated automatically

Reliable opinion

2017-07-11, 09:59

View original

Mariusz

I am a happy owner of a yamaha yzf 125r in which I recently noticed oil loss , I replaced the valve seals which I ordered from gmoto and I am very satisfied , solidly made . Easy to install and fit to my 2010r model I recommend to everyone.

Review translated automatically

Reliable opinion

2020-08-18, 22:09

View original

Jakub

When purchased, the bearing had no play, as befits a new bearing. The bearing has many uses. They can be mounted to wheels that are equipped with a drive on which a very high force acts. This bearing will 100% last more than a typical Chinese bearing.

Review translated automatically

Reliable opinion

2025-07-02, 08:12

View original

Iñaki

It works correctly and was very easy to install. My bike is a 2006 CBF600N and I had no problems at all, it only takes a socket wrench and needle nose pliers to remove and attach the connecting cable.

Review translated automatically

Reliable opinion

2020-11-22, 15:13

View original

Jacek

Yamaha XVS 1300 CU year 2014 The bolt is shorter than the original and does not hold the size of the original bolt. It should not be indicated to fit this model. The only use for it is a copper gasket.

Review translated automatically

Reliable opinion

2021-06-03, 15:15

View original

Sławomir

I own a 2005 Honda CBF600. The sensor fit without a problem, plug and play. The replacement took 5 minutes. Fulfillment of the order was lightning fast, the product was with me the next day. Highly recommend.

Review translated automatically

Reliable opinion

2025-04-23, 06:01

View original

Jens

Fast service. Good place to shop and at a really good price. They ship fast. It's not the last time I shop there.

Review translated automatically

Reliable opinion

2024-08-22, 13:28

View original

Jakub

Very nice gasket does its job, fits perfectly, material is good for this model I recommend honda cb 500 pc 26

Review translated automatically

Reliable opinion

2020-11-17, 08:10

View original

Antek

Gasket made solidly do not protrude pieces of material beyond the lid And no worries about accidental damage during installation.

Review translated automatically

Reliable opinion

2019-04-20, 12:46

View original

Gabriel

Very good quality and workmanship the fit is also ok as I the very way of putting on the valves is quite simple

Review translated automatically

Reliable opinion

2024-08-22, 13:29

View original

Jakub

The water pump gasket fits works seals everything as it should and in sim so much fits I recommend !!!

Review translated automatically

Reliable opinion