Motorcycle engine - parts
Yamaha XJ 650

2020-07-30, 12:06

View original

Darek

The screw is made with precision. I just pay attention to the assembly! The original screw is at least twice as long. The torque recommended in the service book (43Nm) is far too much for a Yamaha Thundercat, fekt is a broken thread.

Review translated automatically

Reliable opinion

2024-10-05, 10:56

View original

Marcin

The instrument according to the description does not fit the Xj600 51J (87). However, I found somewhere on the web information that it is a replacement for Yamaha's YM-01245. According to the service manual, such a designation has a gauge for this motorcycle. So I ordered it and it fits. Operation of this gauge is, contrary to the opinions on the forums, child's play, the key to success is accurate axial installation with the shaft cam and following the service manual. Assembly of the instrument, removal of the valve plate, insertion of a new one, and finally removal of the instrument takes about 5 minutes. On the forums they write that you need to file something or ream the holes - total nonsense! The edge of the head in the place of installation of the gauge is not straight, but runs along a curve, so the gauge adheres to this curve point-wise - it does not matter. Just axial with the cam of the shaft and fits perfectly and the first time. I recommend using this jig- the forum methods of supporting the valves with a clamp make it difficult to remove the valve plate and risk bending the valve! I recommend, it fits Xj600 51j.

Review translated automatically

Reliable opinion

2023-05-24, 10:46

View original

Dawid

A great copper washer for the oil drain bolt. Its main advantage is the right hardness. When tightening, it undergoes plastic deformation, so it perfectly fulfills its role - seals. Beware of washers made of copper alloys. Some of them are so hard that they do not yield even when hit with a hammer - they are not suitable for sealing the oil drain.

Review translated automatically

Reliable opinion

2021-02-07, 13:11

View original

RDS

Some time ago I began to apply the principle of replacing copper washers at the time of oil change (previously I burned out). I must admit that for 1 zl it is not worth fighting with the old washer, especially since you will not get the same effect as with a new one. Now I treat the washer as a mandatory set - I always buy a set of oil + filter + drain bolt washer.

Review translated automatically

Reliable opinion

2017-04-04, 18:03

View original

Grzegorz

My machines WSK M06B3 72r , Jawa 350 TS,Minsk 400, I have been sourcing parts from GMOTO for some time, I recommend because of the sufficient description of products, conformity of parts with the description, fast shipping, great contact. I am passionate about extinct motorcycles (demoluds to be precise), so I require a lot from the goods and here I find it,without unnecessary fuss.

Review translated automatically

Reliable opinion

2024-09-19, 08:55

View original

BOULET-DESBAREAU

The product is very similar to the original. The only fault is that the threaded end is too short compared to the original. It's missing about 5 to 8 mm. This damaged the threads on my housing. I had to dismantle everything and redo the threading with ilsert.

Review translated automatically

Reliable opinion

2025-11-23, 06:52

View original

Bernard

I received the parcel very quickly, the product was very well packaged and corresponded perfectly to the photo and to my expectations. The price is more than interesting. I haven't used it yet, but at first sight it should do the trick without any problem.

Review translated automatically

Reliable opinion

2023-08-18, 11:07

View original

Artur

Everything ok full professionalism and fast delivery ( everything original) plus for remembering the motorcycle on the website and selecting parts by the selected version I will definitely use this store in the future I recommend it

Review translated automatically

Reliable opinion

2020-11-22, 15:13

View original

Jacek

Yamaha XVS 1300 CU year 2014 The bolt is shorter than the original and does not hold the size of the original bolt. It should not be indicated to fit this model. The only use for it is a copper gasket.

Review translated automatically

Reliable opinion

2019-03-04, 06:25

View original

Mirosław

Yamaha wr 450f 2004 sensor for the handle fits without a problem only the plug needs to be replaced with the original. As for the product itself is as described.

Review translated automatically

Reliable opinion