Forgot password
Order status
Free delivery from 150 euro
Motorcycle fuel system - parts
RMMotor PY 50 4T
Options +1 Browse by manufacturer
Products reviews
Zipp Neken 2 50cm3 2019 Installation of the carburetor very easy. Just screw two screws from the carburetor mount, put the throttle on the cable, screw the throttle. Install the air filter. Put on the fuel hose. Put on the manual suction line. I rate the installation of the carburetor as very easy even with no knowledge of mechanics. The carburetor after installation is pre-adjusted ready to drive. Recommended.
Review translated automatically
Reliable opinion
Moped gb Street 50 , on the old original carburetor muddied up on cold engine. No power despite the adjustments made. Today after installing a new carburetor moped revived, a noticeable improvement in engine performance that I had not decided earlier to make this purchase only agonized and combined like the proverbial horse uphill . I recommend this carburetor. It is really worth it.
Review translated automatically
Reliable opinion
I have a Barton sprint I changed the cylinder to 110cc Carburetor fits motor runs flawlessly and intake manifold Professional service I recommend
Review translated automatically
Reliable opinion
Very good quality there is no better I really recommend and the price very attractive And in general I recommend this store good prices and quality
Review translated automatically
Reliable opinion
Ebonite carburettor washer with GY6 4T O-ring has not been installed, as the pipe is the wrong size
Review translated automatically
Reliable opinion
Nozzle an important element when codifying the engine capacity without this element the modification will have no effect in power
Review translated automatically
Reliable opinion
Moped - Barton Fighter Eco 2020 The store's merchandise filter specified as if this pad would fit my machine. It does not fit!!! The main hole is 3.5 mm too small, and worse, the spacing of the screws is also strongly too small. I had an emergency situation and sanded the holes to my needs provisionally. But I am disappointed. For 139FMB engines, GMoto does not carry ebonite washers, despite the fact that these are the most common moped engines in Poland. And I see in the previous comments that this is nothing new.
Review translated automatically
Reliable opinion
Carburettor kit 139FMB DELUX IT'S GOOD, IT FIXED MY CARBURETOR EASY TO INSTALL AND WORKS BEAUTIFULLY NO PROBLEMS WITH IT WERE NOT RECOMMEND THIS PRODUCT BETTER THAN BUYING A NEW CARBURETOR LONG LASTING AND AS I SAID EASY TO INSTALL JUST A TOP PRODUCT, I HAVE NOTHING TO COMPLAIN ABOUT I RECOMMEND!!!!!! AND FOR A BOMB PRICE THE BEST PRODUCT.?? AND IT ALSO GOES ON A JAWA BETKA 50Q 4T
Review translated automatically
Reliable opinion
Hello, I have a repair kit for the gas tank everything fits as it should yesterday and the engine is running as it should, thanks to your store and online site I order what I need and in 1 or 2 days I have my product every time the parts fit and I am satisfied and will probably buy more products from gmoto
Review translated automatically
Reliable opinion
Mám junak 902 chopper rok 2021 o pojemnosti 50 ccm wsedlem na gmoto wiszukal gaznik z dopasowanie do mojej stroje . Unfortunately gaznik tak dopasowany zie wse treba prerabiet from the gas line to the filter tím prosek o zmiany w dopasowanie na czensti Bo to niepasuje produkt chinsky bez jakosti dopraczowania
Review translated automatically
Reliable opinion
I am very satisfied with the purchase of a carburetor with manual suction 139FMB 4T from gmoto.pl. The carburetor is of high quality and works very well. The engine runs smoother now and I save more fuel. I recommend this carburetor to everyone who is looking for a reliable and efficient part for their motorcycle.
Review translated automatically
Reliable opinion
What to write here a lot. I have a moped Romet C1 and it is always difficult to fit some parts to it. In the case of the handle, which I also ordered from this website, I succeeded, but not with the gasket. I do not see the point of sending it back, because it would be a terrible waste of bilge(
Review translated automatically
Reliable opinion
I had a problem with adjusting the carburetor because I went back to 50 cc, now it runs as it should, I replaced the main nozzle from 82 to 72 and now it is great besides I recommend the seller professional service and even express delivery thank you very much
Review translated automatically
Reliable opinion
Zipp Shock 4 t,80ccm. 2009r.The engine (139 fmb) had a problem with the revs (hesitation),and I could not adjust the mixture composition. I disassembled the carburetor,cleaned it,and put it together with the ordered repair kit.The assembly went without problems. It works properly.
Review translated automatically
Reliable opinion
i have a 2007 kingway 50 chopper I bought this nozzle in order to give my bike more power and thanks to it it has certainly a lot more power, it fits perfectly to any carburetor to all those who want to carry out tuning of their motorcycle I RECOMMEND!!!!
Review translated automatically
Reliable opinion
Moped - Barton Fighter Eco 2020 This is not an oring for 139FMB !!! Too small in diameter and too thin. 139FMB has an ebonite washer with a passage diameter of 20.5 mm. This oring, on the other hand, fits a different washer, with a passage diameter of 17 mm.
Review translated automatically
Reliable opinion
Chinese QUAD with 139FMB engine of 50cc capacity. The carburetor works flawlessly. Nicely made and well protected for transport. A moment to put it on, pouring fuel iiiiiiii one shot and so much fun. Highly recommend.
Review translated automatically
Reliable opinion
Hello. The carburetor arrived in quick time. It fits the model I had before, after installing it along with the newly purchased gas line it ignited after a few seconds despite the fact that the quad had been out of service for almost a year.
Review translated automatically
Reliable opinion
The carburetor is good for the price, but it is missing the o-rings on the screws from adjusting the low rpm and the amount of air in the mixture, but for the price, it is really well made, and works very well.
Review translated automatically
Reliable opinion
The product is made of good quality material, which should give us better operation and prolong the life of the product. Replaced in Barton Volcano and there it fits better than the original. Aesthetically it looks respectable
Review translated automatically
Reliable opinion
Hello I purchased a 139FMB 4T manual suction carburetor and I am 100% satisfied with the product finally my gb street works as it should. Quality good, price right, fast delivery.
Review translated automatically
Reliable opinion
I installed it on my carburetor because I thought it was good, even very good, but simply by changing its little parts on the carb I have even more power on my bike.
Review translated automatically
Reliable opinion
Quickly completed order. To install the carburetor you need longer screws than the shaved part. I just purchased the carburetor, it is cold March, evaluate how it performs when I ride a bit.
Review translated automatically
Reliable opinion
i have a 2007 kingway 50 chopper manifold made of good quality material provides long-lasting performance perfectly fits the carburetor and head really recommend to everyone!!!
Review translated automatically
Reliable opinion
My machine is a 4t baotian 50cm scooter after tiuning now 72cm bigger nozzle bigger spigot necessary bigger spigot washer this product meets all the requirements I highly recommend it
Review translated automatically
Reliable opinion
Kingway Chopper Leike 2009 - I received the product brand new, as described. After installation, it works perfectly - standard for a gasifier, a minor adjustment is made to the slow speed.
Review translated automatically
Reliable opinion
Robie czeso purchases and I am satisfied. Motorcycle kingway 110 . package always on time. In the box is in accordance with the description .overall flawless. I am satisfied.I did not carry out repairs.
Review translated automatically
Reliable opinion
Good quality gasifier everything works as it should. Carburetor perfectly adjusted! I am a beginner motorcyclist and I will definitely supply equipment from this company. I recommend 100%
Review translated automatically
Reliable opinion
The carburetor is very well made, it fits kxd/loncin 607 capacity 125. Unfortunately, once my float failed but this is normal in such carburetors. Overall, I recommend the purchase
Review translated automatically
Reliable opinion
Kit useful for carburetor reconditioning Everything fits pz 19 carburetor Throttle valve and needle fits perfectly Set includes all gaskets and adjustment screws
Review translated automatically
Reliable opinion
Quad 110 by bemigermany with TZH152FMH engine (top starter). Carburetor keihin pz20, the nozzle does its job, it is well made, came well packaged, I recommend
Review translated automatically
Reliable opinion
The pad is nicely made, it's a pity that it's made of poor materials, but for a few zlotys you can't expect miracles, but it's worth adding a few zlotys and buying a better one, best regards
Review translated automatically
Reliable opinion
The carburetor fits perfectly and does a great job. The pit bike runs reliably again and starts up well. I can recommend the carburetor with a clear conscience
Review translated automatically
Reliable opinion
I have a 2014 Junak 903 Race 125ccm, the product was a perfect fit for my motorcycle, the installation went really easily, both quality and aesthetics came out very well.
Review translated automatically
Reliable opinion
Nice service, everything as described, super packed and protected, fast shipping. Ebonite carburetor washer with oring super made I recommend this store.
Review translated automatically
Reliable opinion
I bought it because I was afraid I wouldn't have the gasket that matched the carburetor I'd bought, and frankly I'm not disappointed with the quality.
Review translated automatically
Reliable opinion
Magnus Jolly 4T capacity 50 vintage 2008.It is very good quality. With the fit there are no problems,everything fits. It performs its function perfectly.
Review translated automatically
Reliable opinion
Magnus Jolly 4T capacity 50 vintage 2008.It is very good quality. With the fit there are no problems,everything fits. It performs its function perfectly.
Review translated automatically
Reliable opinion
After installation, the motorcycle revived after adjusting the carburetor, the motorcycle began to ride normally. Product well packaged, installation was trivial. I recommend the product.
Review translated automatically
Reliable opinion
Very good product. In addition to the low price. Quick and easy to install. The product works very well I recommend to everyone. I am very satisfied with the product.
Review translated automatically
Reliable opinion