Forgot password
Order status
Free delivery from 150 euro
Motorcycle parts
Honda CB 250 N Euro 1979
Manufacturer
Price
Sort
€118.11
Honda voltage regulator - 681124
Options +2 
€23.39
Lowest price from 30 days before discount: €24.63
Fits on the frontEBC FA 045 brake pads (2 pcs.)
€256.12
Lowest price from 30 days before discount: €269.60
delivery 0 €EBC MD 1036 LS left A brake disc - MD1036LS
€10.29
Gas cable A
€15.25
JMP front automatic stop
€16.46
Lowest price from 30 days before discount: €17.32
Athena 6302 2RS C3 SKF wheel bearing - MS150420130M3
from 4
Browse by manufacturer
Products reviews
Used for Honda FT 500 1983. Fitted within the hour (after disassembly & preparation = removal of old bearings). Have used 50 mm pvc pipe to drive bottom cup in; tightness of fit was as it should be. Did not use the supplied washer but made my own of 30x36x3 mm so the original rubber seal could sit below the (inner part of) the bearing. Re-used the original bottom washer (0.8 mm thick) to shield the seal. The (upper) adjustment nut also carries a thin shield. I had to grind the spigot (for the shield, on the nut) to a chamfer, as it just touched the radius of the upper bearing inner ring. On the 3rd picture, where the shield lies under the nut: red arrows = grind inner dia of spigot, shield fits at outer dia (on top as depicted). Ordered a 2nd set for my Honda XBR 500.
Review translated automatically
Reliable opinion
The screw is made with precision. I just pay attention to the assembly! The original screw is at least twice as long. The torque recommended in the service book (43Nm) is far too much for a Yamaha Thundercat, fekt is a broken thread.
Review translated automatically
Reliable opinion
For my Hondas FT 500 (1983) & XBR 500 (1986) as spares. Remove the lever first, then punch out the old one from the contact pins side; it's an easy, light press fit. When pressing in the new one, align the hook on the switch with the notch in the clutch lever body. Note the hole in the switch also lines up with a hole at the underside of the alu body; it's for contact spray when needed. (Better use it before needed; once corroded the inner contact becomes difficult).
Review translated automatically
Reliable opinion
Honda VTR 1000F, 1998 The chain visually looks sensational, marked on the joints "JTM, 50X2, JAPAN". I have no reservations about the quality of workmanship in comparison with leading brands. However, as for "real quality" I would comment after the season. Protected better than the competition, not paper, but a hard foil that protects against oxidation. The cap comes with X-rings. Everything after installation looks Very Good rating 3 x 5. p.LANDPOST
Review translated automatically
Reliable opinion
Affairs, it conducts electricity. However, it does not fit the 1976 GL1000 K1 model, as it has a larger diameter than the original (factory) and will not go into the hole in the handle holder. I had to take the original one apart despite the damage and was able to repair it. Perhaps this one will fit the specified GL1000 78-79 but I will check this when I give it to a colleague. It would be good to have the basic dimensions plotted on the parts in the photo to see if it will fit us.
Review translated automatically
Reliable opinion
The shipment arrived remarkably quickly, Contact excellent, they answered my question without undue delay. Parts of very good quality, in general, only positives. In an era of online stores that treat customers more like intruders than as employers a great positive. Keep it up; )
Review translated automatically
Reliable opinion
The shipment arrived remarkably quickly, Contact excellent, they answered my question without undue delay. Parts of very good quality, in general, only positives. In an era of online stores that treat customers more like intruders than as employers a great positive. Keep it up; )
Review translated automatically
Reliable opinion
The product is very similar to the original. The only fault is that the threaded end is too short compared to the original. It's missing about 5 to 8 mm. This damaged the threads on my housing. I had to dismantle everything and redo the threading with ilsert.
Review translated automatically
Reliable opinion
Junak M10 from 1963 . Chain length matched to this motorcycle . Service life is about 15 thousand km . We replace before time due to the specific design and entry of the chain into the slider castings . Failure is a tragedy
Review translated automatically
Reliable opinion
Yamaha XVS 1300 CU year 2014 The bolt is shorter than the original and does not hold the size of the original bolt. It should not be indicated to fit this model. The only use for it is a copper gasket.
Review translated automatically
Reliable opinion