Forgot password
Order status
Free delivery from 150 euro
Motorcycle parts
Honda CB 250 T Twin 1977
Manufacturer
Price
Sort
Options +4 
€118.11
Honda voltage regulator - 681124
Podobne:
Podobne:
€15.20
Gas line A
€10.29
Gas cable A
from 4
Browse by manufacturer
Products reviews
Used for Honda FT 500 1983. Fitted within the hour (after disassembly & preparation = removal of old bearings). Have used 50 mm pvc pipe to drive bottom cup in; tightness of fit was as it should be. Did not use the supplied washer but made my own of 30x36x3 mm so the original rubber seal could sit below the (inner part of) the bearing. Re-used the original bottom washer (0.8 mm thick) to shield the seal. The (upper) adjustment nut also carries a thin shield. I had to grind the spigot (for the shield, on the nut) to a chamfer, as it just touched the radius of the upper bearing inner ring. On the 3rd picture, where the shield lies under the nut: red arrows = grind inner dia of spigot, shield fits at outer dia (on top as depicted). Ordered a 2nd set for my Honda XBR 500.
Review translated automatically
Reliable opinion
The screw is made with precision. I just pay attention to the assembly! The original screw is at least twice as long. The torque recommended in the service book (43Nm) is far too much for a Yamaha Thundercat, fekt is a broken thread.
Review translated automatically
Reliable opinion
WSK 125 75r | The frame fits in the org. holes in the rear lamp mount. I recommend, because this product is worth its price and it is practically indispensable in the mounting of the plate.
Review translated automatically
Reliable opinion
I have a Honda CLR 125 , 2002. I bought the fairing glass. I am satisfied with the goods. Good quality. Assembles quickly and without problems. It looks very impressive.
Review translated automatically
Reliable opinion
In this price range, there is nothing to complain about. The product will do its job. It should certainly survive more than one motorcycle trip.
Review translated automatically
Reliable opinion
Kawasaki eliminator ZL 600 1998 year half 600cm windshield installation went through without a problem as it was written and so I mounted.
Review translated automatically
Reliable opinion
Glass concrete. Shipment well protected, the installation itself takes 3 minutes. The motorcycle takes on character. Yamaha XJ 600.
Review translated automatically
Reliable opinion
Product as described, super fit, express delivery.Regards.
Review translated automatically
Reliable opinion
I currently ride a 1999 Yamaha XJ 600N Diversion. The windshield fairing Puig Naked - heavily tinted 100% meets my expectations. Thanks to it, riding at 120 km/h is pleasant, in addition, the motorcycle has not lost its appearance. Despite the inexpensive price, the fairing is made in very good quality, with attention to detail. A huge plus is the inclusion of clear installation instructions and a number of additional mounting adapters that allow a non-technical person to install the fairing in a few minutes using only the tools necessary to remove the front lamp on the motorcycle. The product b. Good quality, at a good price, thanks to additional mounting adapters fits "like a glove" and is easy to install. The fairing significantly increases the comfort of riding.
Review translated automatically
Reliable opinion
For this kind of money, the glass performs superbly. In addition to the glass and mounting brackets, the kit includes a number of different screws needed for installation. The glass fits motorcycles with side lamp holders. Despite its rather small size, the glass shields from the wind quite well. It is known that it is not a full fairing, but it is still better than riding without anything. I rate the quality and installation instructions at 4 with a plus. It is very possible that the windshield over time will catch small scratches on its surface, but what to demand for such money. In general, the glass is worth recommending and without hesitation I would buy it again.
Review translated automatically
Reliable opinion
For my Hondas FT 500 (1983) & XBR 500 (1986) as spares. Remove the lever first, then punch out the old one from the contact pins side; it's an easy, light press fit. When pressing in the new one, align the hook on the switch with the notch in the clutch lever body. Note the hole in the switch also lines up with a hole at the underside of the alu body; it's for contact spray when needed. (Better use it before needed; once corroded the inner contact becomes difficult).
Review translated automatically
Reliable opinion
For a Honda CB 450s motorcycle, the filter fits but I did not put it on because the build quality is poor, compared to another brand I have been using for 12 years. I was curious to see how it looks and whether it was worth putting it on. The FIltr simply has a smaller filtration area. The gaskets from the kit are super matched and this is a mega plus because other brands could take an example from this by adding them to the kit. In conclusion, you can confidently buy for the gaskets alone and treat the filter as a fallback. Regards
Review translated automatically
Reliable opinion
Honda VTR 1000F, 1998 The chain visually looks sensational, marked on the joints "JTM, 50X2, JAPAN". I have no reservations about the quality of workmanship in comparison with leading brands. However, as for "real quality" I would comment after the season. Protected better than the competition, not paper, but a hard foil that protects against oxidation. The cap comes with X-rings. Everything after installation looks Very Good rating 3 x 5. p.LANDPOST
Review translated automatically
Reliable opinion
Affairs, it conducts electricity. However, it does not fit the 1976 GL1000 K1 model, as it has a larger diameter than the original (factory) and will not go into the hole in the handle holder. I had to take the original one apart despite the damage and was able to repair it. Perhaps this one will fit the specified GL1000 78-79 but I will check this when I give it to a colleague. It would be good to have the basic dimensions plotted on the parts in the photo to see if it will fit us.
Review translated automatically
Reliable opinion
2002 Honda Hornet 600 The fairing was purchased to improve the appearance of the motorcycle. Significant changes in airflow I did not notice. The product is very well made. It comes with plenty of screws so that you can freely adjust the fairing. I recommend it to everyone who wants to make their equipment look more attractive. If you are looking for wind protection buy another Puig product at GMOTO! :)
Review translated automatically
Reliable opinion
A great copper washer for the oil drain bolt. Its main advantage is the right hardness. When tightening, it undergoes plastic deformation, so it perfectly fulfills its role - seals. Beware of washers made of copper alloys. Some of them are so hard that they do not yield even when hit with a hammer - they are not suitable for sealing the oil drain.
Review translated automatically
Reliable opinion
Some time ago I began to apply the principle of replacing copper washers at the time of oil change (previously I burned out). I must admit that for 1 zl it is not worth fighting with the old washer, especially since you will not get the same effect as with a new one. Now I treat the washer as a mandatory set - I always buy a set of oil + filter + drain bolt washer.
Review translated automatically
Reliable opinion
My machines WSK M06B3 72r , Jawa 350 TS,Minsk 400, I have been sourcing parts from GMOTO for some time, I recommend because of the sufficient description of products, conformity of parts with the description, fast shipping, great contact. I am passionate about extinct motorcycles (demoluds to be precise), so I require a lot from the goods and here I find it,without unnecessary fuss.
Review translated automatically
Reliable opinion
Unfortunately, the frame is made very poorly, due to carelessly cast material at the edge, the license plate does not fit and it is impossible to close the latches. It is better to spend a few zlotys more for a better quality product that will have the correct dimensions. Despite the not too bad aesthetics, I advise against the product, it does not serve its purpose.
Review translated automatically
Reliable opinion
I bought a fairing for Kawasaki er5, installation very easy and well illustrated in the instructions, the fit is good, a little had to bend the parts to fit perfectly. It looks great and, most importantly, serves its purpose, at speeds of 100-140 a significant improvement in comfort and convenience.
Review translated automatically
Reliable opinion
I bought a fairing for Kawasaki er5, installation very easy and well illustrated in the instructions, the fit is good, a little had to bend the parts to fit perfectly. It looks great and, most importantly, serves its purpose, at speeds of 100-140 a significant improvement in comfort and convenience.
Review translated automatically
Reliable opinion
The shipment arrived remarkably quickly, Contact excellent, they answered my question without undue delay. Parts of very good quality, in general, only positives. In an era of online stores that treat customers more like intruders than as employers a great positive. Keep it up; )
Review translated automatically
Reliable opinion
The purchased fairing from Puig is really of excellent quality. The included mounting kit makes it easy to fit the windshield to our naked model. My CBF 500 is now more perfect. I chose the heavily tinted color and this is how I envisioned it, it fits perfectly.
Review translated automatically
Reliable opinion
The product is very similar to the original. The only fault is that the threaded end is too short compared to the original. It's missing about 5 to 8 mm. This damaged the threads on my housing. I had to dismantle everything and redo the threading with ilsert.
Review translated automatically
Reliable opinion
Frame very cool massive with a cool composing company logo unfortunately I did not use the purchased item because my board is smaller than I anticipated ? but the frame itself I highly recommend as I will measure the size of the board I will order another one like it
Review translated automatically
Reliable opinion
The element is made of good quality plastic, allows for repeated mounting and dismounting. The number and size of the mounting holes allows you to conveniently adjust the mounting of the element. Shape and aesthetics of workmanship at a really good level
Review translated automatically
Reliable opinion
License plate frame very solidly and aesthetically made, the size of the plate perfectly matches the size of the license plate, the mounting holes of the frame even fit into any bracket that are found at the motorcycle.
Review translated automatically
Reliable opinion
Junak M10 from 1963 . Chain length matched to this motorcycle . Service life is about 15 thousand km . We replace before time due to the specific design and entry of the chain into the slider castings . Failure is a tragedy
Review translated automatically
Reliable opinion
Everything ok full professionalism and fast delivery ( everything original) plus for remembering the motorcycle on the website and selecting parts by the selected version I will definitely use this store in the future I recommend it
Review translated automatically
Reliable opinion
Honda St 1300 126 hp 80k hp 2002r , I bought the motorcycle in the commission and there standard commission frame, a little diso-polo with such a ride that's why the frame with the inscription HONDA will perfectly match the new machine ;)
Review translated automatically
Reliable opinion
Yamaha XVS 1300 CU year 2014 The bolt is shorter than the original and does not hold the size of the original bolt. It should not be indicated to fit this model. The only use for it is a copper gasket.
Review translated automatically
Reliable opinion
I have 2 old oilers reliable equipment frames fit like a glove I bought 2 pieces well fitted to the dimensions of the board simple to use good material highly recommend
Review translated automatically
Reliable opinion
Romet scmb 125, I bought a frame for the reg plate.Appearance , size, quality, price - very good. I recommend! Delivery prompt and well packaged.
Review translated automatically
Reliable opinion
What to write. A lot of screw cutouts to fit and screw centrally in each vehicle. Also in a Chinese electric. Fits like a glove.
Review translated automatically
Reliable opinion
Benelli TNT 125 quick and easy installation for everyone. Shipment ordered for parcel machine shipped quickly. I recommend this product to everyone as well as the store.
Review translated automatically
Reliable opinion
This is not the first time I have ordered from Gmoto yet I have not been disappointed shipment always fast on time products also as described I recommend
Review translated automatically
Reliable opinion
The locking element of the plate falls out, so I screwed it on. Once I had a similar patent and lost the plate, then I did not screw.
Review translated automatically
Reliable opinion
Very good workmanship, prompt delivery. Implementation in accordance with the order. Product definitely worth recommending.
Review translated automatically
Reliable opinion
It's a pity that in the feedback there is no option of feedback to deliver, here you should be rated three, the rest as in the best order
Review translated automatically
Reliable opinion
Everything in the best possible order. Frame made of good quality plastic, sheet metal fits it and holds well.
Review translated automatically
Reliable opinion