Forgot password
Order status
Free delivery from 150 euro
Motorcycle parts
Honda CB 650 1982
Manufacturer
Price
Sort
Options +6 
€8.31
6304 2RS C3 SKF bearing
€10.66
Suction cable
€10.29
Clutch cable
€47.79
Honda CB CBX ignition switch
€13.03
Clutch cable
€15.25
JMP front automatic stop
from 6
Browse by manufacturer
Products reviews
Used for Honda FT 500 1983. Fitted within the hour (after disassembly & preparation = removal of old bearings). Have used 50 mm pvc pipe to drive bottom cup in; tightness of fit was as it should be. Did not use the supplied washer but made my own of 30x36x3 mm so the original rubber seal could sit below the (inner part of) the bearing. Re-used the original bottom washer (0.8 mm thick) to shield the seal. The (upper) adjustment nut also carries a thin shield. I had to grind the spigot (for the shield, on the nut) to a chamfer, as it just touched the radius of the upper bearing inner ring. On the 3rd picture, where the shield lies under the nut: red arrows = grind inner dia of spigot, shield fits at outer dia (on top as depicted). Ordered a 2nd set for my Honda XBR 500.
Review translated automatically
Reliable opinion
I do not recommend this plug absolutely. The plug did not withstand the first tightening with a torque wrench much before reaching the proper tightening torque. I can't tell where the positive comments under this product come from, maybe with larger diameter plugs it is better. In my case, a simple oil change ended up with a whole day of disassembling and putting the motorcycle back together to remove the broken thread and the magnesium that fell inside the oil pan. The fit itself is not right either, the original plug has more than twice the thread length.
Review translated automatically
Reliable opinion
Honda NX 500 Dominator 1988 It fits perfectly. It is solid and when it came in contact with the wrench cap, it did not behave like plasticine unlike the old screw. I have already done 1500 kilometers. All in good order. An interesting option with a magnetic tip. I recommend.
Review translated automatically
Reliable opinion
Hello I own a Honda VTR1000 F 1997 I bought a mirror for a small amount of money which is durable, not like the Chinese crap that folds at higher speed and vibrates at slow speed. With a clear conscience I recommend Gmoto.pl store
Review translated automatically
Reliable opinion
1. bolt 12, which is a size 17? The threads fit, but. 2. it cracked while screwing leaving a piece of thread in the oil pan. 3. want to experience a heart attack during an oil change? Only 14.80!
Review translated automatically
Reliable opinion
The screw is professionally made, it holds until nice. It certainly does not drop a drop. The magnet attached to its end is so strong that I had a hard time detaching it from the tool cart. I recommend
Review translated automatically
Reliable opinion
I have a Honda CLR 125 , 2002. I bought the fairing glass. I am satisfied with the goods. Good quality. Assembles quickly and without problems. It looks very impressive.
Review translated automatically
Reliable opinion
The thread of the plug ok and basically that's it. Unfortunately, the magnet practically does not do its job. It's a waste of money for this particular plug.
Review translated automatically
Reliable opinion
Kawasaki eliminator ZL 600 1998 year half 600cm windshield installation went through without a problem as it was written and so I mounted.
Review translated automatically
Reliable opinion
Glass concrete. Shipment well protected, the installation itself takes 3 minutes. The motorcycle takes on character. Yamaha XJ 600.
Review translated automatically
Reliable opinion
The clutch fits the cb 650sc model perfectly Clutch works very well on cold and warm engine I recommend
Review translated automatically
Reliable opinion
Professionally made instrument, a must have for every DIY enthusiast as well as a professional for the garage.
Review translated automatically
Reliable opinion
EBC springs super quality for little money Super made fit perfectly in the slots I recommend the product
Review translated automatically
Reliable opinion
Product as described, super fit, express delivery.Regards.
Review translated automatically
Reliable opinion
I currently ride a 1999 Yamaha XJ 600N Diversion. The windshield fairing Puig Naked - heavily tinted 100% meets my expectations. Thanks to it, riding at 120 km/h is pleasant, in addition, the motorcycle has not lost its appearance. Despite the inexpensive price, the fairing is made in very good quality, with attention to detail. A huge plus is the inclusion of clear installation instructions and a number of additional mounting adapters that allow a non-technical person to install the fairing in a few minutes using only the tools necessary to remove the front lamp on the motorcycle. The product b. Good quality, at a good price, thanks to additional mounting adapters fits "like a glove" and is easy to install. The fairing significantly increases the comfort of riding.
Review translated automatically
Reliable opinion
For this kind of money, the glass performs superbly. In addition to the glass and mounting brackets, the kit includes a number of different screws needed for installation. The glass fits motorcycles with side lamp holders. Despite its rather small size, the glass shields from the wind quite well. It is known that it is not a full fairing, but it is still better than riding without anything. I rate the quality and installation instructions at 4 with a plus. It is very possible that the windshield over time will catch small scratches on its surface, but what to demand for such money. In general, the glass is worth recommending and without hesitation I would buy it again.
Review translated automatically
Reliable opinion
For my Hondas FT 500 (1983) & XBR 500 (1986) as spares. Remove the lever first, then punch out the old one from the contact pins side; it's an easy, light press fit. When pressing in the new one, align the hook on the switch with the notch in the clutch lever body. Note the hole in the switch also lines up with a hole at the underside of the alu body; it's for contact spray when needed. (Better use it before needed; once corroded the inner contact becomes difficult).
Review translated automatically
Reliable opinion
Honda VTR 1000F, 1998 The chain visually looks sensational, marked on the joints "JTM, 50X2, JAPAN". I have no reservations about the quality of workmanship in comparison with leading brands. However, as for "real quality" I would comment after the season. Protected better than the competition, not paper, but a hard foil that protects against oxidation. The cap comes with X-rings. Everything after installation looks Very Good rating 3 x 5. p.LANDPOST
Review translated automatically
Reliable opinion
Affairs, it conducts electricity. However, it does not fit the 1976 GL1000 K1 model, as it has a larger diameter than the original (factory) and will not go into the hole in the handle holder. I had to take the original one apart despite the damage and was able to repair it. Perhaps this one will fit the specified GL1000 78-79 but I will check this when I give it to a colleague. It would be good to have the basic dimensions plotted on the parts in the photo to see if it will fit us.
Review translated automatically
Reliable opinion
2002 Honda Hornet 600 The fairing was purchased to improve the appearance of the motorcycle. Significant changes in airflow I did not notice. The product is very well made. It comes with plenty of screws so that you can freely adjust the fairing. I recommend it to everyone who wants to make their equipment look more attractive. If you are looking for wind protection buy another Puig product at GMOTO! :)
Review translated automatically
Reliable opinion
Honda Dominator NX650 If you are asking yourself whether it makes sense to buy motorcycle accessories by mail order, then calculate the time spent in traffic jams to drive to the stores in search of selected items. My calculation indicates that for a few zlotys it's not worth it to run the car. On Gmoto I found everything I need. Both the price and delivery time are exemplary. I recommend.
Review translated automatically
Reliable opinion
I bought a fairing for Kawasaki er5, installation very easy and well illustrated in the instructions, the fit is good, a little had to bend the parts to fit perfectly. It looks great and, most importantly, serves its purpose, at speeds of 100-140 a significant improvement in comfort and convenience.
Review translated automatically
Reliable opinion
I bought a fairing for Kawasaki er5, installation very easy and well illustrated in the instructions, the fit is good, a little had to bend the parts to fit perfectly. It looks great and, most importantly, serves its purpose, at speeds of 100-140 a significant improvement in comfort and convenience.
Review translated automatically
Reliable opinion
The purchased fairing from Puig is really of excellent quality. The included mounting kit makes it easy to fit the windshield to our naked model. My CBF 500 is now more perfect. I chose the heavily tinted color and this is how I envisioned it, it fits perfectly.
Review translated automatically
Reliable opinion
I have always dreamed of something like this. Finally I could clean the nozzles thoroughly. amol the tips are so sharp that even if you try, you can enlarge the hole in the nozzle to a given size. So not only cleans, but if you want to enlarge the holes. I recommend 100%
Review translated automatically
Reliable opinion
I use exactly this magnetic oil drain screw in every Honda I have. The screw, despite exposure to harsh weather conditions, does not corrode, does not catch deposits and, most importantly, does not leak. The magnet actually catches metallic flecks and does not lose strength.
Review translated automatically
Reliable opinion
Good quality speedo cable, the end caps are original. Unfortunately, although gmoto says this cable is compatible with my HONDA MT80 HD02, it's too short and can't be installed...
Review translated automatically
Reliable opinion
Junak M10 from 1963 . Chain length matched to this motorcycle . Service life is about 15 thousand km . We replace before time due to the specific design and entry of the chain into the slider castings . Failure is a tragedy
Review translated automatically
Reliable opinion
Fits the original Daelim Daystar VL125 carburetor. Thick enough to make the gasket slightly compressed. Nothing but to take while it is ;)
Review translated automatically
Reliable opinion
Bought for 1982 Honda CB 750 custom. Stashed away in storage for now, but they look exactly the same as the others.
Review translated automatically
Reliable opinion
Package sent expeditiously !!!! Product as described. Everything works as it should. I recommend !
Review translated automatically
Reliable opinion