Motorcycle parts
Honda CBF 1000 - Page 11

2018-11-01, 20:15

View original

Krzysztof

I ordered the air vents with the motorcycle Honda XRV 750 Africa Twin - 1999 in mind. They fit the front calipers as well as the rear caliper. After screwing in, there is a little bit of thread sticking out(this is for a small minus), which is covered by a blanking rubber. They successfully replace the original, which is twice as expensive in the service. To the aesthetics and solidity rather can not be complained about - no burrs, the layer of zinc is placed on well-prepared steel. When tightening, care should be taken to select a perfectly matching wrench, scratches and destruction of the zinc layer can result in the appearance of rust in a fairly short time due to the fact that the material is steel. The downgrade for the material is due to the fact that I would prefer stainless steel instead of steel and zinc.

Review translated automatically

Reliable opinion

2020-11-22, 22:44

View original

Piotr

Filter installed on a 2004 Varadero 1000. Filter in a cardboard box additionally protected by a film. Filter gasket moistened with some agent to prevent damage during screwing.

Review translated automatically

Reliable opinion

2019-01-12, 09:03

View original

Andrzej

Honda Cbf 500 2007. Sealers very good quality . Hassle-free installation. You can see at a glance that it is an original product of Athena.Oil burning I have already.I recommend.

Review translated automatically

Reliable opinion

2020-05-03, 00:23

View original

Maciej

Wsk 125 The frame is nice, you can't expect more from a plastic metallized one. It fits my wsk-i nicely. The only big minus is that it did not fit completely in the holes - I had to widen the holes with a drill both at the top and bottom. Other than that, installation was easy. I recommend the product for those who don't mind making up holes.

Review translated automatically

Reliable opinion

2020-03-30, 20:41

View original

Michał

Sealers without complaint. In a rigid and secure package a set of sealers and covers for two leaguers. Assembly trivially easy (for those who like and have an idea of DIY and small repairs). The fit is perfect. So far zero problem and the lags work perfectly in combination with Motul 10W oil.

Review translated automatically

Reliable opinion

2021-05-08, 07:38

View original

Andrzej

Plastic license plate frame looks like a good chrome material I changed the plate because I became the owner of a Suzuki Intruder VL 125 2000 year all in all. Looks super material fine that's why the price very low ugly comes longer.

Review translated automatically

Reliable opinion

2020-07-08, 19:23

View original

Waldemar

My machine is an 86 Honda Shadow VT 1100 . Purchased parts were not dedicated for this vintage , so as a novice user I bought blind and surprisingly they fit . Installation was no problem and the material and workmanship flawless . G Moto and product on pistket . LWG .

Review translated automatically

Reliable opinion

2017-07-11, 09:59

View original

Mariusz

I am a happy owner of a yamaha yzf 125r in which I recently noticed oil loss , I replaced the valve seals which I ordered from gmoto and I am very satisfied , solidly made . Easy to install and fit to my 2010r model I recommend to everyone.

Review translated automatically

Reliable opinion

2017-07-11, 09:59

View original

Mariusz

I am a happy owner of a yamaha yzf 125r in which I recently noticed oil loss , I replaced the valve seals which I ordered from gmoto and I am very satisfied , solidly made . Easy to install and fit to my 2010r modelj recommend to everyone.

Review translated automatically

Reliable opinion

2021-02-15, 09:25

View original

Wiktor

Very good quality product. Easy installation, durable material. Everything is of the highest level. I am not a writer to write fairy tales in the opinion of 100 characters, so I invite you to buy. I heartily recommend.

Review translated automatically

Reliable opinion

2017-11-17, 07:02

View original

Jakub

We fitted the bearings to a 2004 Honda Hornet pc36. The installation went smoothly and the bearings seem indestructible ;) Well, but this is Mc International after all, the top shelf among parts for Japanese ;)

Review translated automatically

Reliable opinion

2019-06-17, 07:58

View original

Damian

In the category of quality/price very nice frame. Strong plastic imitating chrome. Aesthetics at a high level. Lightweight and durable And the license plate enters on contact ( for me a plus because there is no slack). I recommend

Review translated automatically

Reliable opinion

2020-06-29, 18:59

View original

Szymon

The sensor looks like I got a damaged or defective one from the factory. After screwing the nut in, the thread simply broke. I had to screw in the old sensor. I am waiting for a solution to the issue. The rest of the products ok.

Review translated automatically

Reliable opinion

2020-02-02, 11:46

View original

Bartosz

Triumph Street Triple 765 I have been using HIFLOFILTRO filters for years. In the standard version they do their job perfectly. You can the racing version, but for daily riding there is no need for it.

Review translated automatically

Reliable opinion

2024-05-06, 12:46

View original

Oleksandr

I ordered Athena valve cover gasket, I am satisfied with the purchase, fast delivery, good workmanship Made in Japan. And priced cheaper than others. Thank you. I recommend this store :)

Review translated automatically

Reliable opinion

2024-04-13, 07:28

View original

Mariusz

Filters oil, flows on. No problems with pressure or leaking. It looks good on the CBR 600 F4i - by the color you just can't even see it between the exhaust manifolds ;)

Review translated automatically

Reliable opinion

2020-03-30, 20:44

View original

Michał

The protections, compared to the old ones, are slightly wider, more rigid and more "expandable", which makes them fit perfectly into the groove in the lade blocking the sealers.

Review translated automatically

Reliable opinion

2017-09-04, 10:25

View original

Mariusz

frame very nice, put on jawa ts 350 looks very good on this motorcycle, installation also very pleasant immediately changes the name of the motorcycle adds better charm

Review translated automatically

Reliable opinion

2021-02-13, 13:15

View original

Krzysztof

I own a 2015 Honda Goldwing 1800, the oils as well as any products I purchase are always first quality. I recommend to everyone. Installation without any problems.

Review translated automatically

Reliable opinion

2023-06-09, 19:22

View original

Marek

HIFLOFILTRO filter is a very good solution for any motorcycle. And straightforwardly perfect. I used in each of my motorcycle at each mileage. I heartily recommend.

Review translated automatically

Reliable opinion

2024-09-25, 05:27

View original

Filip

Very good solution for those who want to replace the license plate frame with a new one. The price is very affordable. The quality of workmanship is also flawless. I can recommend

Review translated automatically

Reliable opinion

2021-12-15, 09:59

View original

Tomasz

Yamaha XT600 E 3TB 1991 | Sensor well made. On XT/TT 600 models For proper operation, this sensor should be mounted on silicone without a copper gasket.

Review translated automatically

Reliable opinion

2024-05-03, 07:48

View original

Bogusław

Great sealers, they fit nice and tight even though the lag was polished, so far only about 100km after replacement but no drop on the lag, I recommend

Review translated automatically

Reliable opinion

2019-08-26, 12:15

View original

Sławomir

I own a Honda NT650V Deauville. The seals seem solid because of the 2 spring rings. The previous ones only had one such ring.

Review translated automatically

Reliable opinion

2020-08-21, 06:39

View original

Michał

The description does not match the goods I received. The package marked with a sticker (chrome filter) but in the package was a regular black filter.

Review translated automatically

Reliable opinion

2018-03-18, 08:22

View original

Jarosław

Suzuki Intruder 800, seals of good quality, all dimensions met, has been installing for years in various motorcycles, certainly not the last :)

Review translated automatically

Reliable opinion

2023-05-24, 07:13

View original

Remi

Sealers well made, there was no problem with the installation which indicates well-behaved parameters. Tight, oil no longer leaks.

Review translated automatically

Reliable opinion

2020-02-11, 17:50

View original

Piotr

Sealers very good quality not some cheap plastic. There are 2 springs on each sealer. Fast shipping. Recommended.

Review translated automatically

Reliable opinion

2018-05-07, 18:15

View original

Magdalena

WSK M6 B3 1982 Very good quality product easy to install. Fits perfectly, looks very good. Frame worth recommending.

Review translated automatically

Reliable opinion

2023-07-29, 07:17

View original

Sika

Product of good quality as always fast shipping art.I installed in Honda CB 750 Steven fifty degree of difficulty of installation 2/5 I recommend

Review translated automatically

Reliable opinion

2018-01-14, 09:58

View original

Maciej

everything great.consistent with the order,on time and in good quality.this is another purchase from my side that I am satisfied with.

Review translated automatically

Reliable opinion

2024-06-22, 08:03

View original

Rafał

The seals fit suzuki gsx600f. Finally stopped leaking from the suspension and its operation improved significantly. I recommend

Review translated automatically

Reliable opinion

2023-08-14, 15:03

View original

Janek

I have not yet assembled and do not know how with the fragility of the plastic, but from the outside it looks positive. On the back a slight unpainting.

Review translated automatically

Reliable opinion

2018-07-28, 09:39

View original

Artur

Spark plugs I purchased for my Honda VTR 250 motorcycle after installation the motorcycle fired up beautifully the engine work more evenly I recommend it

Review translated automatically

Reliable opinion

2021-12-21, 10:23

View original

Jacek

Honda CBf 600,2010r.The gaskets fit, whether they will work is what I will know after driving a season, they look quite solid.

Review translated automatically

Reliable opinion

2024-09-11, 14:40

View original

Marcin

Very good quality workmanship fit perfectly to the lags 2 sets mounted on Moto and miles fly nothing leaks.

Review translated automatically

Reliable opinion

2021-06-28, 12:41

View original

Tomasz

Kawasaki VN 15 SE from 1991. A set of Athena 41x54x11 front suspension seals - they fit perfectly, like the original.

Review translated automatically

Reliable opinion

2020-05-25, 21:10

View original

Paweł

The frame mounted on the motorcycle and from today it pleases the eye, I did not want to drill the boards and with the product I am satisfied.

Review translated automatically

Reliable opinion

2020-01-24, 08:51

View original

Tomasz

Recommended product very easy to install oring included without any problems recommend to all interested parties

Review translated automatically

Reliable opinion

2020-04-05, 11:54

View original

Tomasz

Honda nt650v deauville 1999. The set of shock seals fit perfectly, the installation was done without any problems.

Review translated automatically

Reliable opinion