Motorcycle parts
Honda CBF 600 - Page 5

2018-11-01, 20:15

View original

Krzysztof

I ordered the air vents with the motorcycle Honda XRV 750 Africa Twin - 1999 in mind. They fit the front calipers as well as the rear caliper. After screwing in, there is a little bit of thread sticking out(this is for a small minus), which is covered by a blanking rubber. They successfully replace the original, which is twice as expensive in the service. To the aesthetics and solidity rather can not be complained about - no burrs, the layer of zinc is placed on well-prepared steel. When tightening, care should be taken to select a perfectly matching wrench, scratches and destruction of the zinc layer can result in the appearance of rust in a fairly short time due to the fact that the material is steel. The downgrade for the material is due to the fact that I would prefer stainless steel instead of steel and zinc.

Review translated automatically

Reliable opinion

2018-11-01, 20:28

View original

Krzysztof

Honda Africa XRV 750 - 1999. I bought 12 pieces. This mounting rubber is found in several places on the motorcycle(the mount of the skull rack, oil cooler, plastic handles, etc.). It looks like the original, the rubber is flexible, you can bend it with two fingers with a stronger squeeze and it looks solid. Only the course of time can verify whether it is as solid. Dimensions: Hole diameter(nominal): 10mm Width of the entire rubber: 22mm Groove depth: 8mm

Review translated automatically

Reliable opinion

2020-03-30, 20:41

View original

Michał

Sealers without complaint. In a rigid and secure package a set of sealers and covers for two leaguers. Assembly trivially easy (for those who like and have an idea of DIY and small repairs). The fit is perfect. So far zero problem and the lags work perfectly in combination with Motul 10W oil.

Review translated automatically

Reliable opinion

2025-08-03, 20:59

View original

Aksel

Have used these gaskets for the valve cover screws and they do exactly what they are supposed to. They seal tight, keep oil in and seem like a definite improvement over worn original gaskets. Installation was easy and the material feels both resilient and durable. No signs of oil sweat after installation - completely satisfied!

Review translated automatically

Reliable opinion

2020-07-08, 19:23

View original

Waldemar

My machine is an 86 Honda Shadow VT 1100 . Purchased parts were not dedicated for this vintage , so as a novice user I bought blind and surprisingly they fit . Installation was no problem and the material and workmanship flawless . G Moto and product on pistket . LWG .

Review translated automatically

Reliable opinion

2017-05-15, 22:44

View original

Maciej

Patient Honda CB600F Hornet, vintage 2001, non-functioning fan switch. What can I say, a top-notch product. After replacement, the fan spins and works at its best. This radiator fan switch is a great product, I would recommend it to anyone

Review translated automatically

Reliable opinion

2023-06-28, 15:29

View original

Bartłomiej

The outer diameter of the gasket is about 1-2mm too large for the 2010 Honda CBF600, after gently spreading the outer muffle of the muffler went in by force (it is soft) and somehow got there after tightening the cybant, but the installation is troublesome.

Review translated automatically

Reliable opinion

2021-03-31, 10:03

View original

Dominik

The seals look decently made. We'll see how with their durability. I'll admit that there were problems with installation and it took some time, but they are finally sitting in place. Now only field tests.

Review translated automatically

Reliable opinion

2017-11-17, 07:02

View original

Jakub

We fitted the bearings to a 2004 Honda Hornet pc36. The installation went smoothly and the bearings seem indestructible ;) Well, but this is Mc International after all, the top shelf among parts for Japanese ;)

Review translated automatically

Reliable opinion

2018-07-17, 12:36

View original

Jakub

Honda vfr750f from 1996. Everything works perfectly. The installation went without any complications I did 2000km a week after installing the new clutch and I have no reservations.

Review translated automatically

Reliable opinion

2021-11-07, 09:59

View original

Marek

Honda Hornet CB600FA PC 41, good quality filter, good fit, my hornet is definitely easier to breathe now. I am satisfied cheap is not but in my opinion worth it.

Review translated automatically

Reliable opinion

2025-09-02, 18:25

View original

Tomáš

The above set of seals for front forks Honda Deauville NT 700 V, r.v. 2008 absolutely fine, trouble-free assembly, the product suits the type of moto, appears to be of good quality.

Review translated automatically

Reliable opinion

2020-03-30, 20:44

View original

Michał

The protections, compared to the old ones, are slightly wider, more rigid and more "expandable", which makes them fit perfectly into the groove in the lade blocking the sealers.

Review translated automatically

Reliable opinion

2023-09-11, 20:14

View original

sara

This mounting rubber is a great replacement for the rubbers found on the Honda CBR 600, but they are slightly smaller than the original (I personally didn't mind the installation)

Review translated automatically

Reliable opinion

2025-09-25, 07:32

View original

Славчо

They did a perfect job for me.The delivery was fast and accurate.And the workmanship itself is perfect the quality is top,the site is very good and accurate and quality which is the most important thing

Review translated automatically

Reliable opinion

2025-04-30, 17:05

View original

Thomas

Bought to replace the original honda bearings, very good quality, fitted just right for the Hornet, very good price. Fast shipping, I recommend.

Review translated automatically

Reliable opinion

2024-05-03, 07:48

View original

Bogusław

Great sealers, they fit nice and tight even though the lag was polished, so far only about 100km after replacement but no drop on the lag, I recommend

Review translated automatically

Reliable opinion

2025-04-13, 11:27

View original

NIKOS

Excellent product. It fit properly in the caliper and I no longer have any leakage from the wear and tear of the previous one. Tourmax quality comparable to the factory ones.

Review translated automatically

Reliable opinion

2019-08-26, 12:15

View original

Sławomir

I own a Honda NT650V Deauville. The seals seem solid because of the 2 spring rings. The previous ones only had one such ring.

Review translated automatically

Reliable opinion

2025-08-07, 09:58

View original

Vincent

Parts corresponding to the original start at a slightly lower temperature 85/90 degrees original start at 100 degrees aesthetics equal to the original

Review translated automatically

Reliable opinion

2025-07-22, 11:06

View original

Stefanos

On CBF 500A applied correctly to the radiator and it works just like the factory switch. It also seals as it should and there are no leaks.

Review translated automatically

Reliable opinion

2025-03-08, 12:28

View original

ixai

The seals and dust cap are of very good quality, also comes with instructions on the correct way to mount the seals in case you don't know how to mount them.

Review translated automatically

Reliable opinion

2023-05-24, 07:13

View original

Remi

Sealers well made, there was no problem with the installation which indicates well-behaved parameters. Tight, oil no longer leaks.

Review translated automatically

Reliable opinion

2020-02-11, 17:50

View original

Piotr

Sealers very good quality not some cheap plastic. There are 2 springs on each sealer. Fast shipping. Recommended.

Review translated automatically

Reliable opinion

2021-02-16, 11:24

View original

Błażej

Gasket ordered for Honda GL500 Interstate '82, good workmanship, fits perfectly - well fitted by the store for this model.

Review translated automatically

Reliable opinion

2025-05-13, 07:11

View original

Kenn

Fit perfectly which I also expected. Would definitely recommend others to order. Relatively fast shipping, but ok

Review translated automatically

Reliable opinion

2023-07-29, 07:17

View original

Sika

Product of good quality as always fast shipping art.I installed in Honda CB 750 Steven fifty degree of difficulty of installation 2/5 I recommend

Review translated automatically

Reliable opinion

2025-07-27, 08:46

View original

Eckehard

Good product delivered quickly. I searched for a while to avoid spending so much and found what I was looking for at GMOTO. That's how it should be.

Review translated automatically

Reliable opinion

2024-06-22, 08:03

View original

Rafał

The seals fit suzuki gsx600f. Finally stopped leaking from the suspension and its operation improved significantly. I recommend

Review translated automatically

Reliable opinion

2025-01-12, 17:44

View original

Barlet

Perfect for my 2004 Hornet. They fit perfectly, good quality for a decent price. Perfect shipping.

Review translated automatically

Reliable opinion

2025-09-10, 09:42

View original

Thomas

The part fitted perfectly. Everything as described and everything went great. Will order again if required.

Review translated automatically

Reliable opinion

2024-09-11, 14:40

View original

Marcin

Very good quality workmanship fit perfectly to the lags 2 sets mounted on Moto and miles fly nothing leaks.

Review translated automatically

Reliable opinion

2024-11-07, 08:28

View original

Furui

Delivered as ordered. Everything in order. I would order from GMoto again. It is a reliable supplier.

Review translated automatically

Reliable opinion

2022-05-02, 11:20

View original

Mirosław

Honda SW t400 year 2010 very good filter, very good workmanship, fits my Honda It met my expectations

Review translated automatically

Reliable opinion

2020-04-05, 11:54

View original

Tomasz

Honda nt650v deauville 1999. The set of shock seals fit perfectly, the installation was done without any problems.

Review translated automatically

Reliable opinion

2019-06-22, 19:15

View original

Grzegorz

Good product - the aphrodite stopped "buzzing" at higher speeds. I also have the impression that it got a bigger kick ;)

Review translated automatically

Reliable opinion

2018-11-22, 19:44

View original

Andrzej

Honda Transalp XL 600 1999. Rubber installed fits it is not orginal but can be goes in its place .

Review translated automatically

Reliable opinion

2022-08-02, 22:26

View original

Andrzej

I own a motorcycle brand: Honda CB 500F 2013 material was well packed, fit and complete.

Review translated automatically

Reliable opinion

2024-09-19, 07:24

View original

VAYSSIE

fast delivery and product responding well to its use no negative points to renew if necessary

Review translated automatically

Reliable opinion

2024-05-02, 15:54

View original

Adrian

Product of very good quality, fit very good, fit the motorcycle for which it was recommended.

Review translated automatically

Reliable opinion