Forgot password
Order status
Free delivery from 150 euro
![Tourmax 7.5 [2.65mm] valve plate.](https://img.gmoto.pl/12312/plytka-zaworowa-sr-75x265mm_1_m2.webp)
Options +2 
Browse by manufacturer
Products reviews
I ordered the air vents with the motorcycle Honda XRV 750 Africa Twin - 1999 in mind. They fit the front calipers as well as the rear caliper. After screwing in, there is a little bit of thread sticking out(this is for a small minus), which is covered by a blanking rubber. They successfully replace the original, which is twice as expensive in the service. To the aesthetics and solidity rather can not be complained about - no burrs, the layer of zinc is placed on well-prepared steel. When tightening, care should be taken to select a perfectly matching wrench, scratches and destruction of the zinc layer can result in the appearance of rust in a fairly short time due to the fact that the material is steel. The downgrade for the material is due to the fact that I would prefer stainless steel instead of steel and zinc.
Review translated automatically
Reliable opinion
Sealers without complaint. In a rigid and secure package a set of sealers and covers for two leaguers. Assembly trivially easy (for those who like and have an idea of DIY and small repairs). The fit is perfect. So far zero problem and the lags work perfectly in combination with Motul 10W oil.
Review translated automatically
Reliable opinion
My machine is an 86 Honda Shadow VT 1100 . Purchased parts were not dedicated for this vintage , so as a novice user I bought blind and surprisingly they fit . Installation was no problem and the material and workmanship flawless . G Moto and product on pistket . LWG .
Review translated automatically
Reliable opinion
Honda CBR F4i 2003. The pins as fit the fairing assembly, quite wide but everywhere where you need to use them whole luckily they are invisible. They did not crack during installation so the quality is fine. Personally I can recommend because I am satisfied.
Review translated automatically
Reliable opinion
Honda st 1300 2002 , the motorcycle has its years at the time of purchase of the machine and the first inspection it turned out that the pins are "worn out" new ones I could not find anywhere , of course on Gmoto there was no problem with the availability ;)
Review translated automatically
Reliable opinion
We fitted the bearings to a 2004 Honda Hornet pc36. The installation went smoothly and the bearings seem indestructible ;) Well, but this is Mc International after all, the top shelf among parts for Japanese ;)
Review translated automatically
Reliable opinion
Honda XL 125 Varadero year 2006. fairing mounting pin fits perfectly, made very solidly, made of strong plastic material. Matched very well to the original, virtually indistinguishable.
Review translated automatically
Reliable opinion
I own a 2005 Honda CBF600. The sensor fit without a problem, plug and play. The replacement took 5 minutes. Fulfillment of the order was lightning fast, the product was with me the next day. Highly recommend.
Review translated automatically
Reliable opinion
Honda CBR F4i 2003. The pins made correctly but if you have a motorcycle like me, they are only suitable from what I noticed for the battery case, the fairing already falls off .
Review translated automatically
Reliable opinion
The protections, compared to the old ones, are slightly wider, more rigid and more "expandable", which makes them fit perfectly into the groove in the lade blocking the sealers.
Review translated automatically
Reliable opinion
Honda Varadero 125 2007r (polift) The pin looks and fits the same literally dot to dot as the original. So I confidently recommend the more that the price is better than in ASO
Review translated automatically
Reliable opinion
For honda CBR 600 F4i sport fit perfectly, the studs, despite the rather high price, are really worth it, there is no play in the fairing joints, which was important for me. I recommend!
Review translated automatically
Reliable opinion
Everything ok, the pin fits nicely and holds the fairing well, even after several times of removing the fairing and driving several thousand kilometers everything holds HONDA CBR F4 2000r.
Review translated automatically
Reliable opinion
Great sealers, they fit nice and tight even though the lag was polished, so far only about 100km after replacement but no drop on the lag, I recommend
Review translated automatically
Reliable opinion
I own a Honda NT650V Deauville. The seals seem solid because of the 2 spring rings. The previous ones only had one such ring.
Review translated automatically
Reliable opinion
Yamaha FJR 1300, vintage 2009, the product does not differ in any way from the original or that purchased from the service. The price for it is dramatically different.
Review translated automatically
Reliable opinion
Sealers well made, there was no problem with the installation which indicates well-behaved parameters. Tight, oil no longer leaks.
Review translated automatically
Reliable opinion
Sealers very good quality not some cheap plastic. There are 2 springs on each sealer. Fast shipping. Recommended.
Review translated automatically
Reliable opinion
Honda Cbr 1100 xx vintage 2005 I recommend this store. Everything without the slightest problem. The package came quickly. Well packaged.
Review translated automatically
Reliable opinion
Product of good quality as always fast shipping art.I installed in Honda CB 750 Steven fifty degree of difficulty of installation 2/5 I recommend
Review translated automatically
Reliable opinion
The seals fit suzuki gsx600f. Finally stopped leaking from the suspension and its operation improved significantly. I recommend
Review translated automatically
Reliable opinion
Honda Shadow VT600 1994. The rubber is not yet attached but, it should fit. the workmanship of these is of a high standard.
Review translated automatically
Reliable opinion
Very good quality workmanship fit perfectly to the lags 2 sets mounted on Moto and miles fly nothing leaks.
Review translated automatically
Reliable opinion
Recommended. 100% satisfaction. Full compatibility. Fast delivery, seamless transaction. Thank you and best regards.
Review translated automatically
Reliable opinion
Honda nt650v deauville 1999. The set of shock seals fit perfectly, the installation was done without any problems.
Review translated automatically
Reliable opinion
Compatible and compared with the original, fits perfectly and holds well the parts to which the attachment was made.
Review translated automatically
Reliable opinion
Very nice workmanship with good strong material fits the caliper perfectly works well on KTM SX 125
Review translated automatically
Reliable opinion
I own a motorcycle brand: Honda CB 500F 2013 material was well packed, fit and complete.
Review translated automatically
Reliable opinion
Honda ST 1300 year 2004 Product made very well. The replacement went without a problem. Rating very good.
Review translated automatically
Reliable opinion
Product of very good quality, fit very good, fit the motorcycle for which it was recommended.
Review translated automatically
Reliable opinion
Product of very good quality, meets my expectations. No need to buy more expensive sealers.
Review translated automatically
Reliable opinion
Honda NTV650 1993. I recommend, good quality product and fast shipping (faster than expected). Greetings
Review translated automatically
Reliable opinion
Everything fits as expected, good quality product, there was no problem with the fit and installation.
Review translated automatically
Reliable opinion
Very nice pegs you can see that they are not made of just anything so I put them on without any problem they look like the original ones
Review translated automatically
Reliable opinion
Honda Varadero 125, a part worth recommending, fits, workmanship good, everything works as expected.
Review translated automatically
Reliable opinion
Everything fits, good value for money. The manufacturing quality of the product is good. Highly recommend.
Review translated automatically
Reliable opinion
Everything fits, good value for money. The manufacturing quality of the product is good. Highly recommend.
Review translated automatically
Reliable opinion
Honda cbr 600 f4i sport - 2002. Bought the mounting wheel which I installed without any problem. I recommend
Review translated automatically
Reliable opinion
CBR F3 600 fits, everything great! Hoods well shaped, rubber bdb quality. I sincerely recommend!
Review translated automatically
Reliable opinion
The gasket fits. Very good product. Why overpay for the original in the service. In a box of 2 pieces.
Review translated automatically
Reliable opinion
We have Motorcycle parts to Honda CBR 600 RR
- Honda CBR 600 RR 2012
- Honda CBR 600 RR ABS 2012
- Honda CBR 600 RR 2007
- Honda CBR 600 RR 2008
- Honda CBR 600 RR 2009
- Honda CBR 600 RR ABS 2009
- Honda CBR 600 RR 2010
- Honda CBR 600 RR ABS 2010
- Honda CBR 600 RR 2011
- Honda CBR 600 RR ABS 2011
- Honda CBR 600 RR 2013
- Honda CBR 600 RRA ABS 2010
- Honda CBR 600 RRA ABS 2011
- Honda CBR 600 RRA ABS 2012
- Honda CBR 600 RRA ABS 2013
- Honda CBR 600 RR 2003
- Honda CBR 600 RR 2014
- Honda CBR 600 RR 2015
- Honda CBR 600 RR 2016
- Honda CBR 600 RRA ABS 2014
- Honda CBR 600 RRA ABS 2015
- Honda CBR 600 RRA ABS 2016
- Honda CBR 600 RR 2004
- Honda CBR 600 RR 2005
- Honda CBR 600 RR 2006
- Honda CBR 600 RR ABS 2014
- Honda CBR 600 RR 2017
- Honda CBR 600 RR ABS 2017
- Honda CBR 600 RR ABS 2023
- Honda CBR 600 RR ABS 2021
- Honda CBR 600 RR ABS 2020
- Honda CBR 600 RR ABS 2019
- Honda CBR 600 RR ABS 2018
- Honda CBR 600 RR 2023
- Honda CBR 600 RR 2021
- Honda CBR 600 RR 2020
- Honda CBR 600 RR 2019
- Honda CBR 600 RR 2018