Motorcycle parts
Honda NT 700 Deauville - Page 4

2018-11-01, 20:15

View original

Krzysztof

I ordered the air vents with the motorcycle Honda XRV 750 Africa Twin - 1999 in mind. They fit the front calipers as well as the rear caliper. After screwing in, there is a little bit of thread sticking out(this is for a small minus), which is covered by a blanking rubber. They successfully replace the original, which is twice as expensive in the service. To the aesthetics and solidity rather can not be complained about - no burrs, the layer of zinc is placed on well-prepared steel. When tightening, care should be taken to select a perfectly matching wrench, scratches and destruction of the zinc layer can result in the appearance of rust in a fairly short time due to the fact that the material is steel. The downgrade for the material is due to the fact that I would prefer stainless steel instead of steel and zinc.

Review translated automatically

Reliable opinion

2018-11-01, 20:28

View original

Krzysztof

Honda Africa XRV 750 - 1999. I bought 12 pieces. This mounting rubber is found in several places on the motorcycle(the mount of the skull rack, oil cooler, plastic handles, etc.). It looks like the original, the rubber is flexible, you can bend it with two fingers with a stronger squeeze and it looks solid. Only the course of time can verify whether it is as solid. Dimensions: Hole diameter(nominal): 10mm Width of the entire rubber: 22mm Groove depth: 8mm

Review translated automatically

Reliable opinion

2021-06-22, 08:54

View original

Sylwek

The filter of a very decent brand. I buy it all the time and have never been disappointed. A very big plus is that it can be unscrewed with a socket wrench. If someone has little space, as I do, to do anything at the filter then such a head on the filter is salvation. It is a little more expensive than the standard version but worth every penny. Last time I had a regular filter I had to perforate it and pour oil in the exhaust pipes to unscrew it , in this case the replacement was clean, fast and above all simple! I recommend

Review translated automatically

Reliable opinion

2020-03-30, 20:41

View original

Michał

Sealers without complaint. In a rigid and secure package a set of sealers and covers for two leaguers. Assembly trivially easy (for those who like and have an idea of DIY and small repairs). The fit is perfect. So far zero problem and the lags work perfectly in combination with Motul 10W oil.

Review translated automatically

Reliable opinion

2023-05-24, 21:04

View original

Dariusz

very good product,easy to install,app to download,connects to your phone via blue tooth and you have everything on the screen of your phone,like charging current,battery condition,monitoring its performance and so on,very useful thing,highly recommend in good conscience

Review translated automatically

Reliable opinion

2019-05-17, 14:01

View original

Przemysław

Honda ST 1300 2002 rubbers fit very good material, they look nice, not everyone remembers that due to worn out rubbers the grip of shoes to the footrests is low which makes it easy to have an accident, safety first and foremost and if by the way the machine gains in appearance it is even better ;)

Review translated automatically

Reliable opinion

2020-07-08, 19:23

View original

Waldemar

My machine is an 86 Honda Shadow VT 1100 . Purchased parts were not dedicated for this vintage , so as a novice user I bought blind and surprisingly they fit . Installation was no problem and the material and workmanship flawless . G Moto and product on pistket . LWG .

Review translated automatically

Reliable opinion

2021-08-08, 10:10

View original

Klaudiusz

Honda CBR 1100XX Super Blackbird from 1997, the replacement went without a problem, the bearings and seals fit. After replacement, you can feel a big improvement and much lighter handling. The old bearings were worn and jumped into the "point" when straightening the steering wheel, now there is no such thing.

Review translated automatically

Reliable opinion

2022-02-07, 10:42

View original

KONRAD

Hello, I bought this kit to stock to keep on the shelf for my Benelli TNT 1130 Gaskets very good company Athena I know and recommend. GMOTO SERVICES ALSO RECOMMEND always professional and without lime well packed and on time recommends and regards

Review translated automatically

Reliable opinion

2024-05-05, 17:43

View original

Wiesław

Filter as described hassle-free installation and a big plus for the ability to tighten with a wrench without using special wrenches for filters. Painting without cavities, and it looks aesthetically pleasing. Plus for the protective film on the filter inlet.

Review translated automatically

Reliable opinion

2016-04-21, 20:49

View original

Julita

Honda Deauville, year 2008, poj.700.Workmanship solid, well-fitted, no problems with installation, meet expectations. We will see how long they will serve :-).It was worth buying, but a piece of rubber should not cost so much ;-).

Review translated automatically

Reliable opinion

2021-03-31, 10:03

View original

Dominik

The seals look decently made. We'll see how with their durability. I'll admit that there were problems with installation and it took some time, but they are finally sitting in place. Now only field tests.

Review translated automatically

Reliable opinion

2017-11-17, 07:02

View original

Jakub

We fitted the bearings to a 2004 Honda Hornet pc36. The installation went smoothly and the bearings seem indestructible ;) Well, but this is Mc International after all, the top shelf among parts for Japanese ;)

Review translated automatically

Reliable opinion

2020-03-30, 20:44

View original

Michał

The protections, compared to the old ones, are slightly wider, more rigid and more "expandable", which makes them fit perfectly into the groove in the lade blocking the sealers.

Review translated automatically

Reliable opinion

2023-09-11, 20:14

View original

sara

This mounting rubber is a great replacement for the rubbers found on the Honda CBR 600, but they are slightly smaller than the original (I personally didn't mind the installation)

Review translated automatically

Reliable opinion

2024-05-03, 07:48

View original

Bogusław

Great sealers, they fit nice and tight even though the lag was polished, so far only about 100km after replacement but no drop on the lag, I recommend

Review translated automatically

Reliable opinion

2019-08-26, 12:15

View original

Sławomir

I own a Honda NT650V Deauville. The seals seem solid because of the 2 spring rings. The previous ones only had one such ring.

Review translated automatically

Reliable opinion

2020-04-20, 09:38

View original

Adrian

Honda CB600 F Hornet, thanks to the possibility of using a ring wrench, the replacement went remarkably fast , it is worth paying a few zlotys extra for this convenience

Review translated automatically

Reliable opinion

2016-05-27, 06:41

View original

Andrzej

-Kawasaki Vulcan EN 500A 1991. -after installation, the tightness of the exhaust system improved -It was definitely worth to buy the above mentioned product.

Review translated automatically

Reliable opinion

2023-05-24, 07:13

View original

Remi

Sealers well made, there was no problem with the installation which indicates well-behaved parameters. Tight, oil no longer leaks.

Review translated automatically

Reliable opinion

2020-02-11, 17:50

View original

Piotr

Sealers very good quality not some cheap plastic. There are 2 springs on each sealer. Fast shipping. Recommended.

Review translated automatically

Reliable opinion

2020-03-31, 10:10

View original

Krzysztof

The product shipped on time, b.well protected, everything efficiently, quickly and reliably , as described. I highly recommend, Krzysiek

Review translated automatically

Reliable opinion

2019-07-05, 22:18

View original

Dawid

Honda Cbr 1100 xx vintage 2005 I recommend this store. Everything without the slightest problem. The package came quickly. Well packaged.

Review translated automatically

Reliable opinion

2023-07-29, 07:17

View original

Sika

Product of good quality as always fast shipping art.I installed in Honda CB 750 Steven fifty degree of difficulty of installation 2/5 I recommend

Review translated automatically

Reliable opinion

2019-07-07, 20:53

View original

Bartłomiej

All ok, well fitted already a few thousand km behind me and all well sealed, nothing sweats Honda CBR 600 F4 2000r.

Review translated automatically

Reliable opinion

2024-06-22, 08:03

View original

Rafał

The seals fit suzuki gsx600f. Finally stopped leaking from the suspension and its operation improved significantly. I recommend

Review translated automatically

Reliable opinion

2024-06-15, 13:21

View original

Serhii

Unfortunately but for Transalp xl600 96r.p. - does not fit. It must be 37x45x25. But the quality is good, for other models must fit.

Review translated automatically

Reliable opinion

2024-01-22, 17:20

View original

Andrzej

Well matched to Nissin brake discs, work well with them, show long service life. Recommended.

Review translated automatically

Reliable opinion

2024-09-11, 14:40

View original

Marcin

Very good quality workmanship fit perfectly to the lags 2 sets mounted on Moto and miles fly nothing leaks.

Review translated automatically

Reliable opinion

2022-05-02, 11:20

View original

Mirosław

Honda SW t400 year 2010 very good filter, very good workmanship, fits my Honda It met my expectations

Review translated automatically

Reliable opinion

2020-04-05, 11:54

View original

Tomasz

Honda nt650v deauville 1999. The set of shock seals fit perfectly, the installation was done without any problems.

Review translated automatically

Reliable opinion

2019-06-22, 19:15

View original

Grzegorz

Good product - the aphrodite stopped "buzzing" at higher speeds. I also have the impression that it got a bigger kick ;)

Review translated automatically

Reliable opinion

2024-02-01, 10:55

View original

Iwona

Compatible and compared with the original, fits perfectly and holds well the parts to which the attachment was made.

Review translated automatically

Reliable opinion

2018-11-22, 19:44

View original

Andrzej

Honda Transalp XL 600 1999. Rubber installed fits it is not orginal but can be goes in its place .

Review translated automatically

Reliable opinion

2022-08-02, 22:26

View original

Andrzej

I own a motorcycle brand: Honda CB 500F 2013 material was well packed, fit and complete.

Review translated automatically

Reliable opinion

2024-05-02, 15:54

View original

Adrian

Product of very good quality, fit very good, fit the motorcycle for which it was recommended.

Review translated automatically

Reliable opinion

2022-04-09, 10:24

View original

Irek

Product of very good quality, meets my expectations. No need to buy more expensive sealers.

Review translated automatically

Reliable opinion

2021-04-05, 10:10

View original

Krzysztof

Honda ST 1300 year 2004 Product very well made replacement went without a problem. Rating very good.

Review translated automatically

Reliable opinion

2024-05-03, 08:20

View original

Krzysztof

It fits and works, and thanks to its special design, it makes replacement much easier. All you need is an ordinary socket wrench.

Review translated automatically

Reliable opinion

2021-11-03, 20:26

View original

Tomasz

Hello, I own a 2008 Kawasaki VN 900 Classic. The hoods fit perfectly. I am satisfied. I recommend.

Review translated automatically

Reliable opinion