Motorcycle parts
Honda ST 1100 Pan European - Page 7

2018-11-01, 20:15

View original

Krzysztof

I ordered the air vents with the motorcycle Honda XRV 750 Africa Twin - 1999 in mind. They fit the front calipers as well as the rear caliper. After screwing in, there is a little bit of thread sticking out(this is for a small minus), which is covered by a blanking rubber. They successfully replace the original, which is twice as expensive in the service. To the aesthetics and solidity rather can not be complained about - no burrs, the layer of zinc is placed on well-prepared steel. When tightening, care should be taken to select a perfectly matching wrench, scratches and destruction of the zinc layer can result in the appearance of rust in a fairly short time due to the fact that the material is steel. The downgrade for the material is due to the fact that I would prefer stainless steel instead of steel and zinc.

Review translated automatically

Reliable opinion

2018-11-01, 20:28

View original

Krzysztof

Honda Africa XRV 750 - 1999. I bought 12 pieces. This mounting rubber is found in several places on the motorcycle(the mount of the skull rack, oil cooler, plastic handles, etc.). It looks like the original, the rubber is flexible, you can bend it with two fingers with a stronger squeeze and it looks solid. Only the course of time can verify whether it is as solid. Dimensions: Hole diameter(nominal): 10mm Width of the entire rubber: 22mm Groove depth: 8mm

Review translated automatically

Reliable opinion

2022-01-08, 09:15

View original

Dariusz

The mounting rubber of the exhaust manifold bracket, and the end muffler, fits tightly and stabilizes them very well, by the way, rumor has it that the TOURMAX brand manufactures OEM parts for HONDA motorcycles, and this can be seen, with disassembled worn parts (markings from casting molds).

Review translated automatically

Reliable opinion

2018-05-30, 16:49

View original

Krzysiek

I have a replica honda magna 2003 year 125ccm I was looking for rectifiers on the internet for a long time and finally found them here fast shipping I fired it up the first time good quality product solid I recommend it

Review translated automatically

Reliable opinion

2019-01-12, 09:03

View original

Andrzej

Honda Cbf 500 2007. Sealers very good quality . Hassle-free installation. You can see at a glance that it is an original product of Athena.Oil burning I have already.I recommend.

Review translated automatically

Reliable opinion

2020-03-30, 20:41

View original

Michał

Sealers without complaint. In a rigid and secure package a set of sealers and covers for two leaguers. Assembly trivially easy (for those who like and have an idea of DIY and small repairs). The fit is perfect. So far zero problem and the lags work perfectly in combination with Motul 10W oil.

Review translated automatically

Reliable opinion

2019-05-17, 14:01

View original

Przemysław

Honda ST 1300 2002 rubbers fit very good material, they look nice, not everyone remembers that due to worn out rubbers the grip of shoes to the footrests is low which makes it easy to have an accident, safety first and foremost and if by the way the machine gains in appearance it is even better ;)

Review translated automatically

Reliable opinion

2020-07-08, 19:23

View original

Waldemar

My machine is an 86 Honda Shadow VT 1100 . Purchased parts were not dedicated for this vintage , so as a novice user I bought blind and surprisingly they fit . Installation was no problem and the material and workmanship flawless . G Moto and product on pistket . LWG .

Review translated automatically

Reliable opinion

2017-07-11, 09:59

View original

Mariusz

I am a happy owner of a yamaha yzf 125r in which I recently noticed oil loss , I replaced the valve seals which I ordered from gmoto and I am very satisfied , solidly made . Easy to install and fit to my 2010r model I recommend to everyone.

Review translated automatically

Reliable opinion

2017-07-11, 09:59

View original

Mariusz

I am a happy owner of a yamaha yzf 125r in which I recently noticed oil loss , I replaced the valve seals which I ordered from gmoto and I am very satisfied , solidly made . Easy to install and fit to my 2010r modelj recommend to everyone.

Review translated automatically

Reliable opinion

2019-04-14, 18:38

View original

Mariusz

KIT purchased and installed on a 1996 Honda VFR 750.Everything fit, it worked, I am satisfied. I will mention that I met with very friendly service. And I guess this is the main reason that I will be shopping there. No photo because the parts are already installed.

Review translated automatically

Reliable opinion

2016-04-21, 20:49

View original

Julita

Honda Deauville, year 2008, poj.700.Workmanship solid, well-fitted, no problems with installation, meet expectations. We will see how long they will serve :-).It was worth buying, but a piece of rubber should not cost so much ;-).

Review translated automatically

Reliable opinion

2019-04-09, 08:40

View original

Rafał

I purchased the bearings with seals a few days ago for my Honda cbr 1000 f sc 21 motorcycle. The parts came to me in no time. At the moment they are waiting for installation because I have to wait until the wheel returns from painting

Review translated automatically

Reliable opinion

2017-11-17, 07:02

View original

Jakub

We fitted the bearings to a 2004 Honda Hornet pc36. The installation went smoothly and the bearings seem indestructible ;) Well, but this is Mc International after all, the top shelf among parts for Japanese ;)

Review translated automatically

Reliable opinion

2021-06-03, 15:15

View original

Sławomir

I own a 2005 Honda CBF600. The sensor fit without a problem, plug and play. The replacement took 5 minutes. Fulfillment of the order was lightning fast, the product was with me the next day. Highly recommend.

Review translated automatically

Reliable opinion

2019-12-27, 13:32

View original

Mariusz

Honda Shadow VT 600 1994. The kit includes all the gaskets that need to be replaced when reconditioning the brake caliper, plus grease for the piston. Everything fit as in the original.

Review translated automatically

Reliable opinion

2020-03-30, 20:44

View original

Michał

The protections, compared to the old ones, are slightly wider, more rigid and more "expandable", which makes them fit perfectly into the groove in the lade blocking the sealers.

Review translated automatically

Reliable opinion

2023-09-11, 20:14

View original

sara

This mounting rubber is a great replacement for the rubbers found on the Honda CBR 600, but they are slightly smaller than the original (I personally didn't mind the installation)

Review translated automatically

Reliable opinion

2020-11-17, 12:27

View original

Mateusz

As it is Athena seals are doing a cool job, 0 leaks so far, every moto of mine so far has just had Athena seals/rings and it has always been git.

Review translated automatically

Reliable opinion

2019-03-12, 09:52

View original

Robert

Battery fitted to Honda Varadero XL 1000 motorcycle very good quality product, very good value for money, very nice and fast service recommend.

Review translated automatically

Reliable opinion

2019-04-27, 15:09

View original

Tomasz

Honda Vfr 750 rc 24 from 1987. The fit of the parts is very good making it a pleasure to assemble the exhaust system. It met my expectations as much as possible.

Review translated automatically

Reliable opinion

2024-05-03, 07:48

View original

Bogusław

Great sealers, they fit nice and tight even though the lag was polished, so far only about 100km after replacement but no drop on the lag, I recommend

Review translated automatically

Reliable opinion

2019-08-26, 12:15

View original

Sławomir

I own a Honda NT650V Deauville. The seals seem solid because of the 2 spring rings. The previous ones only had one such ring.

Review translated automatically

Reliable opinion

2017-06-18, 21:11

View original

Konrad

As great a plus as possible. The product in full working order, I recommend it as much as possible. I looked in many stores and here I found the cheapest. Price/quality 10/10.

Review translated automatically

Reliable opinion

2018-03-18, 08:22

View original

Jarosław

Suzuki Intruder 800, seals of good quality, all dimensions met, has been installing for years in various motorcycles, certainly not the last :)

Review translated automatically

Reliable opinion

2021-04-06, 09:16

View original

Bartłomiej

2014 Honda CRF 250 M Worn with oil to make it go in easier. They fit well, the suspension does not leak. At the next change I will also choose them.

Review translated automatically

Reliable opinion

2023-05-24, 07:13

View original

Remi

Sealers well made, there was no problem with the installation which indicates well-behaved parameters. Tight, oil no longer leaks.

Review translated automatically

Reliable opinion

2020-02-11, 17:50

View original

Piotr

Sealers very good quality not some cheap plastic. There are 2 springs on each sealer. Fast shipping. Recommended.

Review translated automatically

Reliable opinion

2024-09-02, 15:06

View original

Dawid

Very good product, nicely packaged and quality also at a high level, everything fit without any problem, so the CBR F2 is already laughing :d

Review translated automatically

Reliable opinion

2019-07-05, 22:18

View original

Dawid

Honda Cbr 1100 xx vintage 2005 I recommend this store. Everything without the slightest problem. The package came quickly. Well packaged.

Review translated automatically

Reliable opinion

2023-07-29, 07:17

View original

Sika

Product of good quality as always fast shipping art.I installed in Honda CB 750 Steven fifty degree of difficulty of installation 2/5 I recommend

Review translated automatically

Reliable opinion

2018-01-14, 09:58

View original

Maciej

everything great.consistent with the order,on time and in good quality.this is another purchase from my side that I am satisfied with.

Review translated automatically

Reliable opinion

2020-10-26, 17:04

View original

Mariusz

Honda Shadow 1100 ACE 1996, Front brake repair kit identical to the original, when assembled everything fits perfectly.

Review translated automatically

Reliable opinion

2024-06-22, 08:03

View original

Rafał

The seals fit suzuki gsx600f. Finally stopped leaking from the suspension and its operation improved significantly. I recommend

Review translated automatically

Reliable opinion

2018-07-28, 09:39

View original

Artur

Spark plugs I purchased for my Honda VTR 250 motorcycle after installation the motorcycle fired up beautifully the engine work more evenly I recommend it

Review translated automatically

Reliable opinion

2021-12-21, 10:23

View original

Jacek

Honda CBf 600,2010r.The gaskets fit, whether they will work is what I will know after driving a season, they look quite solid.

Review translated automatically

Reliable opinion

2020-03-27, 07:47

View original

Mirosław

Honda Shadow VT600 1994. The rubber is not yet attached but, it should fit. the workmanship of these is of a high standard.

Review translated automatically

Reliable opinion

2024-09-11, 14:40

View original

Marcin

Very good quality workmanship fit perfectly to the lags 2 sets mounted on Moto and miles fly nothing leaks.

Review translated automatically

Reliable opinion

2021-06-28, 12:41

View original

Tomasz

Kawasaki VN 15 SE from 1991. A set of Athena 41x54x11 front suspension seals - they fit perfectly, like the original.

Review translated automatically

Reliable opinion

2022-06-30, 23:54

View original

Maciej

Suzuki DR 350 1992 gaskets very well made, fit in the original lagi, installation seamless, recommend.

Review translated automatically

Reliable opinion