Motorcycle parts
Honda ST 1300 Pan European - Page 5

2018-11-01, 20:15

View original

Krzysztof

I ordered the air vents with the motorcycle Honda XRV 750 Africa Twin - 1999 in mind. They fit the front calipers as well as the rear caliper. After screwing in, there is a little bit of thread sticking out(this is for a small minus), which is covered by a blanking rubber. They successfully replace the original, which is twice as expensive in the service. To the aesthetics and solidity rather can not be complained about - no burrs, the layer of zinc is placed on well-prepared steel. When tightening, care should be taken to select a perfectly matching wrench, scratches and destruction of the zinc layer can result in the appearance of rust in a fairly short time due to the fact that the material is steel. The downgrade for the material is due to the fact that I would prefer stainless steel instead of steel and zinc.

Review translated automatically

Reliable opinion

2018-11-01, 20:28

View original

Krzysztof

Honda Africa XRV 750 - 1999. I bought 12 pieces. This mounting rubber is found in several places on the motorcycle(the mount of the skull rack, oil cooler, plastic handles, etc.). It looks like the original, the rubber is flexible, you can bend it with two fingers with a stronger squeeze and it looks solid. Only the course of time can verify whether it is as solid. Dimensions: Hole diameter(nominal): 10mm Width of the entire rubber: 22mm Groove depth: 8mm

Review translated automatically

Reliable opinion

2020-11-22, 22:44

View original

Piotr

Filter installed on a 2004 Varadero 1000. Filter in a cardboard box additionally protected by a film. Filter gasket moistened with some agent to prevent damage during screwing.

Review translated automatically

Reliable opinion

2020-05-03, 00:23

View original

Maciej

Wsk 125 The frame is nice, you can't expect more from a plastic metallized one. It fits my wsk-i nicely. The only big minus is that it did not fit completely in the holes - I had to widen the holes with a drill both at the top and bottom. Other than that, installation was easy. I recommend the product for those who don't mind making up holes.

Review translated automatically

Reliable opinion

2019-05-17, 14:01

View original

Przemysław

Honda ST 1300 2002 rubbers fit very good material, they look nice, not everyone remembers that due to worn out rubbers the grip of shoes to the footrests is low which makes it easy to have an accident, safety first and foremost and if by the way the machine gains in appearance it is even better ;)

Review translated automatically

Reliable opinion

2021-05-08, 07:38

View original

Andrzej

Plastic license plate frame looks like a good chrome material I changed the plate because I became the owner of a Suzuki Intruder VL 125 2000 year all in all. Looks super material fine that's why the price very low ugly comes longer.

Review translated automatically

Reliable opinion

2017-04-28, 11:56

View original

Krzysztof

Honda CBR F4i 2003. The pins as fit the fairing assembly, quite wide but everywhere where you need to use them whole luckily they are invisible. They did not crack during installation so the quality is fine. Personally I can recommend because I am satisfied.

Review translated automatically

Reliable opinion

2016-04-21, 20:49

View original

Julita

Honda Deauville, year 2008, poj.700.Workmanship solid, well-fitted, no problems with installation, meet expectations. We will see how long they will serve :-).It was worth buying, but a piece of rubber should not cost so much ;-).

Review translated automatically

Reliable opinion

2019-05-17, 13:59

View original

Przemysław

Honda st 1300 2002 , the motorcycle has its years at the time of purchase of the machine and the first inspection it turned out that the pins are "worn out" new ones I could not find anywhere , of course on Gmoto there was no problem with the availability ;)

Review translated automatically

Reliable opinion

2021-02-15, 09:25

View original

Wiktor

Very good quality product. Easy installation, durable material. Everything is of the highest level. I am not a writer to write fairy tales in the opinion of 100 characters, so I invite you to buy. I heartily recommend.

Review translated automatically

Reliable opinion

2017-11-17, 07:02

View original

Jakub

We fitted the bearings to a 2004 Honda Hornet pc36. The installation went smoothly and the bearings seem indestructible ;) Well, but this is Mc International after all, the top shelf among parts for Japanese ;)

Review translated automatically

Reliable opinion

2020-09-20, 14:21

View original

Rafał

Honda XL 125 Varadero year 2006. fairing mounting pin fits perfectly, made very solidly, made of strong plastic material. Matched very well to the original, virtually indistinguishable.

Review translated automatically

Reliable opinion

2019-06-17, 07:58

View original

Damian

In the category of quality/price very nice frame. Strong plastic imitating chrome. Aesthetics at a high level. Lightweight and durable And the license plate enters on contact ( for me a plus because there is no slack). I recommend

Review translated automatically

Reliable opinion

2020-06-29, 18:59

View original

Szymon

The sensor looks like I got a damaged or defective one from the factory. After screwing the nut in, the thread simply broke. I had to screw in the old sensor. I am waiting for a solution to the issue. The rest of the products ok.

Review translated automatically

Reliable opinion

2020-02-02, 11:46

View original

Bartosz

Triumph Street Triple 765 I have been using HIFLOFILTRO filters for years. In the standard version they do their job perfectly. You can the racing version, but for daily riding there is no need for it.

Review translated automatically

Reliable opinion

2024-04-13, 07:28

View original

Mariusz

Filters oil, flows on. No problems with pressure or leaking. It looks good on the CBR 600 F4i - by the color you just can't even see it between the exhaust manifolds ;)

Review translated automatically

Reliable opinion

2017-04-28, 11:52

View original

Krzysztof

Honda CBR F4i 2003. The pins made correctly but if you have a motorcycle like me, they are only suitable from what I noticed for the battery case, the fairing already falls off .

Review translated automatically

Reliable opinion

2023-09-11, 20:14

View original

sara

This mounting rubber is a great replacement for the rubbers found on the Honda CBR 600, but they are slightly smaller than the original (I personally didn't mind the installation)

Review translated automatically

Reliable opinion

2022-07-23, 13:57

View original

Wiktor

Honda Varadero 125 2007r (polift) The pin looks and fits the same literally dot to dot as the original. So I confidently recommend the more that the price is better than in ASO

Review translated automatically

Reliable opinion

2017-09-04, 10:25

View original

Mariusz

frame very nice, put on jawa ts 350 looks very good on this motorcycle, installation also very pleasant immediately changes the name of the motorcycle adds better charm

Review translated automatically

Reliable opinion

2021-02-13, 13:15

View original

Krzysztof

I own a 2015 Honda Goldwing 1800, the oils as well as any products I purchase are always first quality. I recommend to everyone. Installation without any problems.

Review translated automatically

Reliable opinion

2018-12-04, 08:49

View original

Grzegorz

For honda CBR 600 F4i sport fit perfectly, the studs, despite the rather high price, are really worth it, there is no play in the fairing joints, which was important for me. I recommend!

Review translated automatically

Reliable opinion

2023-06-09, 19:22

View original

Marek

HIFLOFILTRO filter is a very good solution for any motorcycle. And straightforwardly perfect. I used in each of my motorcycle at each mileage. I heartily recommend.

Review translated automatically

Reliable opinion

2024-09-25, 05:27

View original

Filip

Very good solution for those who want to replace the license plate frame with a new one. The price is very affordable. The quality of workmanship is also flawless. I can recommend

Review translated automatically

Reliable opinion

2021-12-15, 09:59

View original

Tomasz

Yamaha XT600 E 3TB 1991 | Sensor well made. On XT/TT 600 models For proper operation, this sensor should be mounted on silicone without a copper gasket.

Review translated automatically

Reliable opinion

2019-07-07, 20:55

View original

Bartłomiej

Everything ok, the pin fits nicely and holds the fairing well, even after several times of removing the fairing and driving several thousand kilometers everything holds HONDA CBR F4 2000r.

Review translated automatically

Reliable opinion

2020-08-21, 06:39

View original

Michał

The description does not match the goods I received. The package marked with a sticker (chrome filter) but in the package was a regular black filter.

Review translated automatically

Reliable opinion

2020-11-17, 09:25

View original

Jacek

Yamaha FJR 1300, vintage 2009, the product does not differ in any way from the original or that purchased from the service. The price for it is dramatically different.

Review translated automatically

Reliable opinion

2018-05-07, 18:15

View original

Magdalena

WSK M6 B3 1982 Very good quality product easy to install. Fits perfectly, looks very good. Frame worth recommending.

Review translated automatically

Reliable opinion

2019-07-05, 22:18

View original

Dawid

Honda Cbr 1100 xx vintage 2005 I recommend this store. Everything without the slightest problem. The package came quickly. Well packaged.

Review translated automatically

Reliable opinion

2024-05-21, 20:40

View original

Mariusz

The sealer seems to be of good quality, I think it will serve well. It fits perfectly soon I will check it in the course of work.

Review translated automatically

Reliable opinion

2018-01-14, 09:58

View original

Maciej

everything great.consistent with the order,on time and in good quality.this is another purchase from my side that I am satisfied with.

Review translated automatically

Reliable opinion

2023-08-14, 15:03

View original

Janek

I have not yet assembled and do not know how with the fragility of the plastic, but from the outside it looks positive. On the back a slight unpainting.

Review translated automatically

Reliable opinion

2018-07-28, 09:39

View original

Artur

Spark plugs I purchased for my Honda VTR 250 motorcycle after installation the motorcycle fired up beautifully the engine work more evenly I recommend it

Review translated automatically

Reliable opinion

2021-12-21, 10:23

View original

Jacek

Honda CBf 600,2010r.The gaskets fit, whether they will work is what I will know after driving a season, they look quite solid.

Review translated automatically

Reliable opinion

2020-05-25, 21:10

View original

Paweł

The frame mounted on the motorcycle and from today it pleases the eye, I did not want to drill the boards and with the product I am satisfied.

Review translated automatically

Reliable opinion

2020-01-24, 08:51

View original

Tomasz

Recommended product very easy to install oring included without any problems recommend to all interested parties

Review translated automatically

Reliable opinion

2019-06-22, 19:15

View original

Grzegorz

Good product - the aphrodite stopped "buzzing" at higher speeds. I also have the impression that it got a bigger kick ;)

Review translated automatically

Reliable opinion

2022-01-30, 08:29

View original

Andrzej

Honda CBF600 PC43 - has been using for years, quality is sufficient with annual oil change interval and quiet driving.

Review translated automatically

Reliable opinion

2018-07-31, 11:56

View original

Kacper

There is nothing much to describe here the candle works great fits daelim daystar 125 I am fully satisfied

Review translated automatically

Reliable opinion