Forgot password
Order status
Free delivery from 150 euro
Browse by manufacturer
Products reviews
I ordered the air vents with the motorcycle Honda XRV 750 Africa Twin - 1999 in mind. They fit the front calipers as well as the rear caliper. After screwing in, there is a little bit of thread sticking out(this is for a small minus), which is covered by a blanking rubber. They successfully replace the original, which is twice as expensive in the service. To the aesthetics and solidity rather can not be complained about - no burrs, the layer of zinc is placed on well-prepared steel. When tightening, care should be taken to select a perfectly matching wrench, scratches and destruction of the zinc layer can result in the appearance of rust in a fairly short time due to the fact that the material is steel. The downgrade for the material is due to the fact that I would prefer stainless steel instead of steel and zinc.
Review translated automatically
Reliable opinion
Honda Africa XRV 750 - 1999. I bought 12 pieces. This mounting rubber is found in several places on the motorcycle(the mount of the skull rack, oil cooler, plastic handles, etc.). It looks like the original, the rubber is flexible, you can bend it with two fingers with a stronger squeeze and it looks solid. Only the course of time can verify whether it is as solid. Dimensions: Hole diameter(nominal): 10mm Width of the entire rubber: 22mm Groove depth: 8mm
Review translated automatically
Reliable opinion
Sealers without complaint. In a rigid and secure package a set of sealers and covers for two leaguers. Assembly trivially easy (for those who like and have an idea of DIY and small repairs). The fit is perfect. So far zero problem and the lags work perfectly in combination with Motul 10W oil.
Review translated automatically
Reliable opinion
My machine is an 86 Honda Shadow VT 1100 . Purchased parts were not dedicated for this vintage , so as a novice user I bought blind and surprisingly they fit . Installation was no problem and the material and workmanship flawless . G Moto and product on pistket . LWG .
Review translated automatically
Reliable opinion
Honda CBR F4i 2003. The pins as fit the fairing assembly, quite wide but everywhere where you need to use them whole luckily they are invisible. They did not crack during installation so the quality is fine. Personally I can recommend because I am satisfied.
Review translated automatically
Reliable opinion
Patient Honda CB600F Hornet, vintage 2001, non-functioning fan switch. What can I say, a top-notch product. After replacement, the fan spins and works at its best. This radiator fan switch is a great product, I would recommend it to anyone
Review translated automatically
Reliable opinion
Honda XL 125 Varadero year 2006. fairing mounting pin fits perfectly, made very solidly, made of strong plastic material. Matched very well to the original, virtually indistinguishable.
Review translated automatically
Reliable opinion
XL 600VA 1987 item easy to use does not require instructions. I recommend this product. Very good quality product for its price. Fast delivery hassle-free service. I recommend
Review translated automatically
Reliable opinion
The protections, compared to the old ones, are slightly wider, more rigid and more "expandable", which makes them fit perfectly into the groove in the lade blocking the sealers.
Review translated automatically
Reliable opinion
This mounting rubber is a great replacement for the rubbers found on the Honda CBR 600, but they are slightly smaller than the original (I personally didn't mind the installation)
Review translated automatically
Reliable opinion
Honda Varadero 125 2007r (polift) The pin looks and fits the same literally dot to dot as the original. So I confidently recommend the more that the price is better than in ASO
Review translated automatically
Reliable opinion
For honda CBR 600 F4i sport fit perfectly, the studs, despite the rather high price, are really worth it, there is no play in the fairing joints, which was important for me. I recommend!
Review translated automatically
Reliable opinion
Honda Transalp xl650 2001 year. The installation of the gaskets went smoothly, good fit , good workmanship and material quality . After installation the carburetor works like new.
Review translated automatically
Reliable opinion
Everything ok, the pin fits nicely and holds the fairing well, even after several times of removing the fairing and driving several thousand kilometers everything holds HONDA CBR F4 2000r.
Review translated automatically
Reliable opinion
I am really satisfied with the purchased bolt. It is well made and meets my expectations, it is a good choice, I will definitely order something again and more than once.
Review translated automatically
Reliable opinion
Great sealers, they fit nice and tight even though the lag was polished, so far only about 100km after replacement but no drop on the lag, I recommend
Review translated automatically
Reliable opinion
I own a Honda NT650V Deauville. The seals seem solid because of the 2 spring rings. The previous ones only had one such ring.
Review translated automatically
Reliable opinion
It works 100% pity only that the kit does not include a copper washer. To seal the connection. Other than that, the product is of good quality. I really recommend
Review translated automatically
Reliable opinion
Yamaha FJR 1300, vintage 2009, the product does not differ in any way from the original or that purchased from the service. The price for it is dramatically different.
Review translated automatically
Reliable opinion
Sealers well made, there was no problem with the installation which indicates well-behaved parameters. Tight, oil no longer leaks.
Review translated automatically
Reliable opinion
Sealers very good quality not some cheap plastic. There are 2 springs on each sealer. Fast shipping. Recommended.
Review translated automatically
Reliable opinion
Product of good quality as always fast shipping art.I installed in Honda CB 750 Steven fifty degree of difficulty of installation 2/5 I recommend
Review translated automatically
Reliable opinion
The seals fit suzuki gsx600f. Finally stopped leaking from the suspension and its operation improved significantly. I recommend
Review translated automatically
Reliable opinion
Tourmax quality is similar to OEM. I've been buying for the third time in a row and I'm satisfied. I recommend and will definitely return to GMOTO ;)
Review translated automatically
Reliable opinion
Gaskets like gaskets :) They fit and seal well. No unnecessary lint. They fit a 1984 Honda Sabre 750.
Review translated automatically
Reliable opinion
Very good quality workmanship fit perfectly to the lags 2 sets mounted on Moto and miles fly nothing leaks.
Review translated automatically
Reliable opinion
Recommended. 100% satisfaction. Full compatibility. Fast delivery, seamless transaction. Thank you and best regards.
Review translated automatically
Reliable opinion
Honda nt650v deauville 1999. The set of shock seals fit perfectly, the installation was done without any problems.
Review translated automatically
Reliable opinion
Good product - the aphrodite stopped "buzzing" at higher speeds. I also have the impression that it got a bigger kick ;)
Review translated automatically
Reliable opinion
Honda Transalp XL 600 1999. Rubber installed fits it is not orginal but can be goes in its place .
Review translated automatically
Reliable opinion
Very nice workmanship with good strong material fits the caliper perfectly works well on KTM SX 125
Review translated automatically
Reliable opinion
I own a motorcycle brand: Honda CB 500F 2013 material was well packed, fit and complete.
Review translated automatically
Reliable opinion
Product of very good quality, fit very good, fit the motorcycle for which it was recommended.
Review translated automatically
Reliable opinion
Product of very good quality, meets my expectations. No need to buy more expensive sealers.
Review translated automatically
Reliable opinion
Honda HRV 750 Africa twin rd04 - fits without any problem, installation very efficient, goods as expected.
Review translated automatically
Reliable opinion
Everything fits as expected, good quality product, there was no problem with the fit and installation.
Review translated automatically
Reliable opinion
Low quality, product well matched to the motorcycle but still the dimensions did not fit could not be used.
Review translated automatically
Reliable opinion
Very nice pegs you can see that they are not made of just anything so I put them on without any problem they look like the original ones
Review translated automatically
Reliable opinion
Honda Varadero 125, a part worth recommending, fits, workmanship good, everything works as expected.
Review translated automatically
Reliable opinion
Everything fits, good value for money. The manufacturing quality of the product is good. Highly recommend.
Review translated automatically
Reliable opinion