Forgot password
Order status
Free delivery from 150 euro
Motorcycle parts
MZ TS 250 1973
Manufacturer
Price
Sort
Options +3 
Browse by manufacturer
Products reviews
My motorcycle is a 1981 Mz Ts 250 restored in original condition.In the summer season I use the motorcycle extensively and I had to purchase a right mirror because it is a mandatory requirement in a motorcycle.The mirror is well made,materials of good quality,visibility of the reflection in the mirror is very good.I recommend the product because it is a good alternative and a compromise between good workmanship and low price.
Review translated automatically
Reliable opinion
Money thrown down the drain in the front lights bulbs 5W and in the original I have 21W I thought what's the problem I'll put the old ones and here's the problem they don't fit, you can't screw on the cover of the turn signal, now on these bulbs blink very quickly you need to look for the orginals
Review translated automatically
Reliable opinion
SHL M04 1953r balls of good quality what is most important they are round and very decent plating as for me they meet all expectations highly recommend
Review translated automatically
Reliable opinion
MZ ETZ 251 washer of good quality fits perfectly on the shaft enters without any play eliminates the play of the carrier I recommend
Review translated automatically
Reliable opinion
Motorcycle MZ TS 250 year of production 1975 shield fitted to the rear wheel made of strong plastic.
Review translated automatically
Reliable opinion
Balls like balls looks like good durable stuff. I'll ride around and see if anything happens to them or not.
Review translated automatically
Reliable opinion
Jawa 50 mustang 1981 / Original frame head bearings have balls with a diameter of 5mm, while these are 6mm. I think that even looking at the shape of the cup they are too large . As far as Wsk is concerned they will fit as much as possible . Very good price and as Gmoto has already accustomed me . Super fast shipping and nicely protected products . Best regards to motomaniacs
Review translated automatically
Reliable opinion
I have a single axle agria tractor with an engine from mz, 60s or 70s, capacity unknown, but now I know it spoils the carburetor from mz 150, but I ordered an oversized carburetor from mz 250, looks solid, clean, neat and solid. Assembly very simple just put on the ferrules and twist with a screwdriver, install the gas line and fuel hose.
Review translated automatically
Reliable opinion
I own a WSK B3 motorcycle with a 125 engine which I modified to look like a cross thanks to GMoto company I was able to complete the restoration process of this motorcycle and I am very pleased with such fast delivery from this store I will certainly buy more than one product from this seller. Best regards and have a nice day.
Review translated automatically
Reliable opinion
Balls made in an exemplary manner, perfectly rounded, dimensions 1:1 with the original, most importantly made of very hard material, and this is the most important because in the end it depends on these balls whether the rod will not fall apart while driving on uneven ground. Once again, I emphasize the workmanship and fit exemplary
Review translated automatically
Reliable opinion
A worthless product, The designers intended the thin corrugated washer to cancel the play between the carrier and the clutch depending on the seating on the cone.The washer on offer is about 1mm thick and not even a sledgehammer will bend it. It can be used as a washer to nail the tar paper.
Review translated automatically
Reliable opinion
Product ok, no major philosophy here, plastic clearance sensor. The original one was probably made of vinyl and broke off for me when removing, plastic is more durable, more flexible, it may serve. At this point it looks ok :) although perfect is not.
Review translated automatically
Reliable opinion
Parts perfectly replace the original ones, they also work very well in the Mosquito. If you are not sure if they will be good, believe they will definitely be perfect for your motorcycle. One set is enough for two garlands. I heartily recommend this product.
Review translated automatically
Reliable opinion
MZ ETZ 250 - lever bouncer rubber, it went into the socket fitfully, the rubber is of good quality, I already have one installed a few years ago ( same store) does not crack does not delaminate, very well serves its purpose.You can confidently install.
Review translated automatically
Reliable opinion
Liebe Freunde, leider ist dieser Kolbenbolzen nicht für die MZ ETZ 250 251 geeignet! Der gelieferte Kolbenbolzen hat Durchmesser 12 mm, im Orginal ist ein Kolbenbolzen von 18 mm im Durchmesser verbaut. Viele Grüße Bernd aus 09557
Review translated automatically
Reliable opinion
The cover gave a perfect fit to the rest of the drivetrain housing. The material seems to be solid and durable. Also, the price of the item is surprising in relation to the rapid storm of price increases. Greetings
Review translated automatically
Reliable opinion
Simson S51 E/4. A poorer and cheaper version of the S51 E in terms of electrical system, identical to the S51 N model. It had a 4-speed transmission. Production ended in 1988. Assembly mileage very easy.
Review translated automatically
Reliable opinion
The turn signals came to me in good condition but unfortunately I sent back due to the fact that the turn signals came on plastic mounts. The photo is not consistent with the delivered product. This was the case with mine
Review translated automatically
Reliable opinion
It fits, but you need to replace the counter drive with the bracket from mz ETZ 150 together with the cable. The original MZ TS 150 drive from the bagelite cover is too short. after replacing the other parts, the meter works fine.
Review translated automatically
Reliable opinion