Forgot password
Order status
Free delivery from 150 euro
Motorcycle parts
Romet Ogar 200
Options +3 
Browse by manufacturer
Products reviews
Hello, I have recently purchased linings for jaws for rometa ogara 200.I highly recommend this product very well fitted and most importantly it is aesthetically made.The product from this website is very quickly delivered by our brave couriers.When I bought the same product only from allegro the jaws were not as required as those from Gmoto.pl. sorry for the quality of the photos but I have a poor camera in my phone
Review translated automatically
Reliable opinion
Carburetor very decently made,easy to install,holds the dimensions of the original. The engine fired up immediately after installation,it was enough only to adjust the slow speed screw and drive. It is worth buying new gaskets for installation, of course. The included hose was flexible and of good quality, while the filter came of a different type - rectangular and not round. Installed in a Jawa 20 armored.
Review translated automatically
Reliable opinion
Greetings. I have used the light switch - zinc in my two motorcycles: A '63 Junak m10 and a '66 SHL 175. This product works perfectly in both cases. To the eye it looks excellent, but what is important is also a product that is easy to install and works correctly in further exploration. I recommend, in my case it works without complaint . Regards
Review translated automatically
Reliable opinion
Greetings. WSK B1 from 1969 The faucet fits and I must say that it is made solidly and also looks quite well slightly imitates the style of bygone times. When you unscrew the cap the thread fits superbly to the tank. One thing that I modified is this longer tube I shortened because in my opinion it reaches too high. Regards and field. Krzysztof
Review translated automatically
Reliable opinion
Warm welcome. WSK B1 of 1969. I applied such a nut to the front brake cable rod. It is a little smaller than the one I have on the rear brake rod, although both on thread 6. It looks nice and at the same time serves its purpose. I recommend and greetings
Review translated automatically
Reliable opinion
Thread reduction used to repair the Romet head, fits most of the communist vehicles, it is easy to repair the damaged head yourself, all you need is a drill and a threader of the right size.
Review translated automatically
Reliable opinion
RECOMMEND !!! Store super :) have all the parts - contact satisfactory.Good quality parts - large selection Fast delivery ! ! ! Effects of work and new parts in the picture :)
Review translated automatically
Reliable opinion
The rod is fine, although the original one has a minimally longer adjustment range (another tip I do not cling to, you can bend it yourself, anyway no one will notice the difference).
Review translated automatically
Reliable opinion
Romet Ogar 200 r.prod 1986. the switch fits perfectly. It works as it should and looks ok, also recommend at my place it works perfectly.
Review translated automatically
Reliable opinion
Hello I have a WSK 175 I replaced the spokes.Quality very good, material and workmanship also very good. It fits perfectly to the rim.
Review translated automatically
Reliable opinion
Romet 50-T-3 Rubber very good quality, installation was quick and efficient no problems. Product worth recommending
Review translated automatically
Reliable opinion
Romet komar 80 r pret aesthetically made but in my exemplazu turned out to be zakrudki about 5 cm I had to improvise
Review translated automatically
Reliable opinion
Ok, they do their job. They look nice and there is no problem putting them on. I recommend and encourage you to buy
Review translated automatically
Reliable opinion
Romet Ogar 200, 1986 Ciego is very nice only so what if it does not fit, it is just too long.
Review translated automatically
Reliable opinion
This is the second time I used such a reduction. The first time as well as the second time it fit perfectly. I recommend!!!
Review translated automatically
Reliable opinion
Used in SHL Gazelle M17, passenger footrest rubber, good quality material, goods as described.
Review translated automatically
Reliable opinion
Mz etz 250 material good and workmanship Great nice appearance, workmanship aesthetic. I recommend!!!
Review translated automatically
Reliable opinion
Komar 2350 , ogar 205 . Rubber very well made , installation went without a problem ,
Review translated automatically
Reliable opinion
Of course, the goods as much as possible to fit a motorcycle which is a WSK 125. The goods in the first term I received damaged (the hole for the cable was missing), but after filing a complaint, the staff ensured that they would send the goods complete, which is a big plus on their part ( in the second term the goods arrived complete and very quickly). I have no objection to discourage the purchase of this merchandise, so I recommend it, because in case of failure of the rope it saves and helps to get home efficiently.
Review translated automatically
Reliable opinion
Moped peda but made in China 2007 year 50 capacity. The product is too weak it let go after 30 min of riding. The hole for the cable was too small I had to enlarge and besides, the broken end of the cable will always be flared and with a larger diameter so you will not do it quickly on the street. I recommend buying a new cable and not playing with replacements. Replacing the cable will do in an hour if you have never done it and the cost is 20 - 30 zl. In the picture it is made of brass and they sent a different one.
Review translated automatically
Reliable opinion
The only type of screw worth buying for clutch adjustment. I went through a lot of these screws until I came across this one and whenever I do an engine I choose this one why? And because the problem was always like this: if the tappet was of good quality and hard, it ate the screw and the adjustment ended quickly, and if the screw hit a good one, it ate the tappet. Buying this screw plus tappet ended my problems with adjusting the clutch. Very durable material.
Review translated automatically
Reliable opinion
I own a classic Ogar 200 with Jawa engine - I bought a set of clutch adjustment screw plus clutch pusher. The adjustment screw is simply fabulous, so far I have been combining with ordinary screws that quickly wore out - here everything fit adjustment very convenient. However, in the clutch pusher I miss the recess at the ends for the ball and spigot of the adjustment screw - as it was in the original parts.
Review translated automatically
Reliable opinion
Romet Ogar 200 '89, Footrests well made, I thought there would be a problem with installation due to the square hole, and thus the inability to rotate the rubber, but it is enough to tap lightly with a hammer to make the rubbers slide into place. As for the aesthetics - on the one hand you can see subtle imperfections in the casting, but they are not too conspicuous, otherwise a very good quality product.
Review translated automatically
Reliable opinion
Ogar 200 88' In my opinion, this is a must-have item when replacing the kick seal. The old plate was sitting so tight , that pulling it out in a state for reassembly was impossible. The plate can be pushed into place without any problem by a long 16 mm socket. It sits securely and holds the o-ring well, which means that oil leaks stopped after replacing the o-ring and plate.
Review translated automatically
Reliable opinion
They seem to be better than the previous black-painted ones, those bent from the weight of the legs, while in my case the problem was that the outer diameter of these rods which gives rubber is 10 mm and not 12 as in the black, I had to press the footrest rubbers on hot glue and surprisingly holds so far.In addition, went in the primer and color to be sure.
Review translated automatically
Reliable opinion
At the "connection" of the rod to the foot yoke, the safety feature is a pin, and the eye itself is only bent at 90 degrees instead of about 180 degrees. If the pin is lost, the brake rod falls out, which is rather optimistic. I recommend a slight overtightening of the ear, however, due to the hole for the pin, it may break for us.
Review translated automatically
Reliable opinion
Bushings very solid to rometa kadet fit I bought more as if they died. I recommend the purchase and the store. I am surprised by the honesty of the store. I made an order then a second basket and they returned the cash and made in one order. The second situation with the lamp for rometa cheapened they removed the basket and made with a lower price. I recommend the store
Review translated automatically
Reliable opinion
komar 2350,I recently purchased a set of tires with detkki, mounting went without the slightest problem, the tire without interference with the key jumped into place under the influence of pumping, tires have a very similar tread to the tires ,,stomil,, the product is properly made, looks solid, time will show how durable it is, I recommend !
Review translated automatically
Reliable opinion
The sleeve is nowhere near the sleeves coming out in the wsk. In a motorcycle wsk came out with a minimum diameter fi 10mm not threaded and in this case we have a roller furniture nut. This is the first time such a thing has happened to me since I have been shopping in this company. Complain nothing because it is not worth the trouble. Too little value.
Review translated automatically
Reliable opinion
Clutch rgulation screw, yes made very nicely, but for my Ogara 200 did not fit, because its fi is smaller, in my case it is fi 6mm. An important thing, nowhere is it stated that the clutch deregulation (rotation of this screw) should be done very slowly, literally 1/4 turn (left-right).
Review translated automatically
Reliable opinion
Romet Ogar 205, well-made set, satisfactory quality and appearance, fits well in the hand, non-slip material is a pleasant alternative to the original plastic handles, increases safety. Installation requires force, but for that the rubber stiffly holds in place, no play.
Review translated automatically
Reliable opinion
Very nicely made, the rubber shines like dog bells. The hole they have is 10mm x 10mm. so at mine I had to scoop a little with a rubber hammer but that's the way it's supposed to be if it's going to hold well - the dimensions of the passenger footrest bar are 12mm x 12mm but it went in ;). WSK 125 GIL, M06B3, engine S01-Z3A.
Review translated automatically
Reliable opinion
Repairing Jawe 50 on gmoto you can count on, here you can buy everything you need, even every smallest detail such as brake bushings, etc. dealing with the overhaul of vintage mopeds or motorcycles there are parts that can not be repaired or is not worth it, and that is why gmoto is ok.
Review translated automatically
Reliable opinion
The ideal thing in a difficult situation when the thread of the plug is already leaking or completely broken. Without having to look for a new head (sometimes unobtainable or at a horrendous price) even in the garage having a stand drill you can repair the damage and continue to enjoy your oldtimer.
Review translated automatically
Reliable opinion
SHL M 11 The bushing has no dimensions, it is not suitable for anything. I do not understand why it is on offer if it does not fit? Hardly, it appears on many sites for various motorcycles and it is an exaggeration to put on the site Junak M10 M 07 where, after all, such a component in this motorcycle does not occur.
Review translated automatically
Reliable opinion
Romet Kadet. Before installing the gasket, I recommend sanding the surface of the faucet knob to get rid of pitting, because whatever the gasket is, fuel will escape through the pitting. If someone does not have mechanical sense, I recommend buying a complete faucet, which is a few zlotys more expensive.
Review translated automatically
Reliable opinion
The product I bought on Gmoto.pl was delivered to me in the same condition as in the pictures, zero hidden defects, in my opinion, after the not high price, the product deserves five ★★★★★, I highly recommend the website Gmoto.pl, friendly service and reasonable prices of parts !!!
Review translated automatically
Reliable opinion
The supplier showed professionalism regarding the preparation AND delivery of the shipment of parts for Junak M10. I was very impressed by the electronic notification system of the status of the order until delivery to the addressee. Very fast delivery and without courier.
Review translated automatically
Reliable opinion
Metal fuel faucet is a solid and durable product that ensures reliability during refueling. Its metal construction guarantees resistance to mechanical damage and weather conditions. In addition, the aesthetic appearance can add style and elegance to the vehicle.
Review translated automatically
Reliable opinion
Motorcycle wsk 125 year 1979 when installing it is best to grease the rubber slightly to get it to go in, because it is hard, but this shows the good quality of the material. Another drumstick has been with me for 5 years and continues to hold without a single crack. I can heartily recommend this product.
Review translated automatically
Reliable opinion