Manufacturer
Price
Sort
Browse by manufacturer
Products reviews
2018-11-01, 20:15
Krzysztof
I ordered the air vents with the motorcycle Honda XRV 750 Africa Twin - 1999 in mind. They fit the front calipers as well as the rear caliper. After screwing in, there is a little bit of thread sticking out(this is for a small minus), which is covered by a blanking rubber. They successfully replace the original, which is twice as expensive in the service. To the aesthetics and solidity rather can not be complained about - no burrs, the layer of zinc is placed on well-prepared steel. When tightening, care should be taken to select a perfectly matching wrench, scratches and destruction of the zinc layer can result in the appearance of rust in a fairly short time due to the fact that the material is steel. The downgrade for the material is due to the fact that I would prefer stainless steel instead of steel and zinc.
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2019-03-31, 12:52
Michał
The GS 500 motorcycle is a machine that I use every day. It gets no concessionary fare and has to endure all sorts of roads. Sometimes fast riding on the expressway, sometimes touring on rough and bumpy roads. The result of this effort is a broken head frame bearing, which bravely endured all the forces acting on the motorcycle. It was time for a bearing from the proven Tourmax company, which I got very quickly thanks to the Gmoto.pl store. The package came quickly, well packed. Goods of the highest quality. Since the replacement of the bearing nothing has happened to the motorcycle and you can confidently continue the season.
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2017-05-15, 21:39
Wiesław
Suzuki GSX-R 1100 motorcycle from 1987 . Due to its age I decided to replace the front master cylinder , searching through the offers I came across a repair kit at gmoto.pl and decided to purchase it along with the brake lever that works with the piston and may have been worn out . The parts after unpacking turned out to be not different in appearance and quality from the original with the included box of special grease . With the assembly there was no problem . All parts fit and work as intended .
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2025-04-14, 07:12
Karl
I was rebuilding my carburettor and decided to replace the diaphragms as well. These diaphragms fit perfectly and bike runs without issues. While installing you do need to be careful not to damage the diaphragms though, as you need to carefully stretch them around the holding piece.
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2017-11-04, 10:28
Patryk
I own a 2003 Suzuki DL 1000 motorcycle. Reperature of the front brake master cylinder I needed because it began to leak and go hard. The replacement is not difficult and the parts fit well. Even without instructions there are no problems to assemble everything correctly ;)
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2021-08-11, 08:17
Boszu
Valves of good quality, fit seamlessly into the Yamaha Thunderace 1000. The only minor insignificant difference, the wire at the top of the valve does not fully close only is such a letter "L". But this does not interfere with anything. After installation it works elegantly. :)
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2020-03-09, 14:54
Paweł
I purchased a kit for a Honda Varadero. Previously installed was still the original. This one qualitatively looks just like the original, I hope it will serve as much. To the undecided I recommend, the only sensible replacement.
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
2022-04-18, 21:14
Sławomir
The bearings matched. They are ok, I will see how long they last supposedly Japanese quality. The price is also acceptable. They are not the cheapest or the most expensive. I do not know what else to write about the bearings. I recommend.
Review translated automatically
-
Esthetics:
-
Material quality:
-
Fitting:
Reliable opinion
Other models of
- Suzuki GSF 1200 SA Bandit ABS 2000
- Suzuki GSF 1200 S Bandit 2005
- Suzuki GSF 1200 SA Bandit ABS 2006
- Suzuki GSF 1200 A Bandit ABS 2006
- Suzuki GSF 1200 Bandit 1996
- Suzuki GSF 1200 Bandit 1997
- Suzuki GSF 1200 Bandit 1998
- Suzuki GSF 1200 Bandit 2000
- Suzuki GSF 1200 Bandit 2001
- Suzuki GSF 1200 Bandit 2002
- Suzuki GSF 1200 Bandit 2003
- Suzuki GSF 1200 Bandit 2004
- Suzuki GSF 1200 Bandit 2005
- Suzuki GSF 1200 Bandit 2006
- Suzuki GSF 1200 S Bandit 1996
- Suzuki GSF 1200 S Bandit 1997
- Suzuki GSF 1200 S Bandit 1998
- Suzuki GSF 1200 S Bandit 1999
- Suzuki GSF 1200 S Bandit 2000
- Suzuki GSF 1200 S Bandit 2001
- Suzuki GSF 1200 S Bandit 2002
- Suzuki GSF 1200 S Bandit 2003
- Suzuki GSF 1200 S Bandit 2004
- Suzuki GSF 1200 S Bandit 2006
- Suzuki GSF 1200 SA Bandit ABS 1997
- Suzuki GSF 1200 SA Bandit ABS 1998
- Suzuki GSF 1200 SA Bandit ABS 1999
- Suzuki GSF 1200 SZA Bandit ABS 2005
- Suzuki GSF 1200 SZ Bandit 2005
- Suzuki GSF 1200 SA Bandit ABS 2001
- Suzuki GSF 1200 SA Bandit ABS 2002










