Motorcycle suspension - parts
Honda CB 500 K Four 1974

2020-02-25, 22:28

View original

Johan

Used for Honda FT 500 1983. Fitted within the hour (after disassembly & preparation = removal of old bearings). Have used 50 mm pvc pipe to drive bottom cup in; tightness of fit was as it should be. Did not use the supplied washer but made my own of 30x36x3 mm so the original rubber seal could sit below the (inner part of) the bearing. Re-used the original bottom washer (0.8 mm thick) to shield the seal. The (upper) adjustment nut also carries a thin shield. I had to grind the spigot (for the shield, on the nut) to a chamfer, as it just touched the radius of the upper bearing inner ring. On the 3rd picture, where the shield lies under the nut: red arrows = grind inner dia of spigot, shield fits at outer dia (on top as depicted). Ordered a 2nd set for my Honda XBR 500.

Review translated automatically

Reliable opinion

2019-04-12, 07:04

View original

Rafal

I own a motorcycle Daelim Daystar vl 125 prod. year 2006 . Lag seals from ATHENA was a successful purchase because they eliminated leakage from the shock absorbers. Easy and quick installation.P olecam.

Review translated automatically

Reliable opinion

2023-06-26, 15:34

View original

Przemysław

Professional approach to the customer, assistance at every stage and reliable. Express service, quality at the highest level, great and close-knit team.

Review translated automatically

Reliable opinion

2022-04-24, 13:31

View original

Krystian

Motorcycle enduro Beta RR 50 delivery went smoothly Sealers easy to install and despite riding on heavy terrain do not let go I recommend highly.

Review translated automatically

Reliable opinion

2025-10-14, 11:40

View original

salmon Sébastien

The equipment is exactly as described. Very good value for money. Delivery was very fast. Site to recommend

Review translated automatically

Reliable opinion

2024-10-13, 16:12

View original

Niko

okay but they are too wide so you have to leave one of the prongs out of the shocks to fit and a bit too hard

Review translated automatically

Reliable opinion

2018-10-23, 18:45

View original

Karol

I own a 2004 Yamahe dt 50 r.The product made very well easy to install.The product did its job as much as possible.

Review translated automatically

Reliable opinion

2020-04-05, 08:45

View original

Tomasz

Honda NSR 125 2002.Solid quality workmanship after installation nothing leaks everything holds well. I recommend!

Review translated automatically

Reliable opinion

2025-05-25, 15:12

View original

Silvio

I liked it. You were great and the fit was perfect. They were very difficult to get in but no problem

Review translated automatically

Reliable opinion

2023-06-30, 12:51

View original

Rafał

Recommended. The product is consistent with the photo. Carefully packed in foil, you can see that no one rummaged at it.

Review translated automatically

Reliable opinion

2020-04-17, 17:42

View original

Michał

Hyosung gt 125 on telescopes (not upside down) from 2006 fits perfectly and finally the lags do not leak.

Review translated automatically

Reliable opinion

2017-04-17, 10:05

View original

Kamil

Sealers very good quality athena,I installed in MOTORHISZPANI rx50,highly recommend

Review translated automatically

Reliable opinion

2018-05-24, 10:42

View original

piotr

Motorcycle romet crs 125 of 2011 everything fits nicely.So far I am satisfied nothing leaks

Review translated automatically

Reliable opinion

2022-08-17, 10:22

View original

Hubert

Unfortunately, the mechanic said that these sealers do not fit the lags of my '82 yamaha xj 550 maxim.

Review translated automatically

Reliable opinion