Motorcycle parts
Honda VF 750 - Page 8

2018-11-01, 20:15

View original

Krzysztof

I ordered the air vents with the motorcycle Honda XRV 750 Africa Twin - 1999 in mind. They fit the front calipers as well as the rear caliper. After screwing in, there is a little bit of thread sticking out(this is for a small minus), which is covered by a blanking rubber. They successfully replace the original, which is twice as expensive in the service. To the aesthetics and solidity rather can not be complained about - no burrs, the layer of zinc is placed on well-prepared steel. When tightening, care should be taken to select a perfectly matching wrench, scratches and destruction of the zinc layer can result in the appearance of rust in a fairly short time due to the fact that the material is steel. The downgrade for the material is due to the fact that I would prefer stainless steel instead of steel and zinc.

Review translated automatically

Reliable opinion

2018-11-01, 20:28

View original

Krzysztof

Honda Africa XRV 750 - 1999. I bought 12 pieces. This mounting rubber is found in several places on the motorcycle(the mount of the skull rack, oil cooler, plastic handles, etc.). It looks like the original, the rubber is flexible, you can bend it with two fingers with a stronger squeeze and it looks solid. Only the course of time can verify whether it is as solid. Dimensions: Hole diameter(nominal): 10mm Width of the entire rubber: 22mm Groove depth: 8mm

Review translated automatically

Reliable opinion

2025-09-22, 15:11

View original

Jordi

Honda Cb500 PC26 - 1994 Includes the parts needed to repair the front brake master cylinder. These are not the original Honda parts, but they are good quality and fit the brake pump perfectly.

Review translated automatically

Reliable opinion

2018-05-30, 16:49

View original

Krzysiek

I have a replica honda magna 2003 year 125ccm I was looking for rectifiers on the internet for a long time and finally found them here fast shipping I fired it up the first time good quality product solid I recommend it

Review translated automatically

Reliable opinion

2019-01-12, 09:03

View original

Andrzej

Honda Cbf 500 2007. Sealers very good quality . Hassle-free installation. You can see at a glance that it is an original product of Athena.Oil burning I have already.I recommend.

Review translated automatically

Reliable opinion

2021-02-02, 22:02

View original

Daniel

99r Honda VFR 800 FI RC46. Simple quick installation. Filter adapted for an ordinary ring wrench. Uses k&n products great look and performance. I recommend

Review translated automatically

Reliable opinion

2024-09-20, 12:07

View original

Aurélien

Purchased to completely rebuild my Nissin 11mm master cylinder. The kit fits perfectly. My master cylinder is back for life.

Review translated automatically

Reliable opinion

2019-03-10, 10:47

View original

Mirosław

Kawasaki Z900. The filter is better made than the original. Very good ease of installation,I am 100% satisfied and recommend to everyone.

Review translated automatically

Reliable opinion

2019-03-15, 08:51

View original

Dominik

Honda varadero 125 XL. Replacement quick and easy. Candles of very good quality. The transaction went well. I recommend

Review translated automatically

Reliable opinion

2021-10-08, 12:10

View original

Artur

There is nothing to say about Hiflo and the quality of their products, so I usually choose their filters.

Review translated automatically

Reliable opinion

2022-03-31, 10:27

View original

Dariusz

Fitting filter for Kawasaki versys KLE 650 , the advantage of it is that it has a key cap .it is ok

Review translated automatically

Reliable opinion

2021-06-29, 10:25

View original

Leszek

Honda XL 600 V Transalp. A filter like a filter, it's hard to judge it by eye. It screwed in easily and pleasantly. All indications are that it filters as God has commanded. Shouldn't there be an o-ring in the place where it is screwed onto the spigot protruding from the block? I can't hide the fact that I would be happy to win four hundred bucks because I need a clutch and cash is tight.

Review translated automatically

Reliable opinion

2022-09-28, 18:40

View original

Stanisław

Honda NTV 650 Revere 97r. Kit well made, good quality parts, easy installation good fit. Replaces the original parts well, the pump works flawlessly. I would like to add that the kit was purchased on the recommendation of a Honda service employee because the original repair kit costs almost 4 times as much, and this one does its job 100%. I sincerely recommend.

Review translated automatically

Reliable opinion

2020-03-30, 20:41

View original

Michał

Sealers without complaint. In a rigid and secure package a set of sealers and covers for two leaguers. Assembly trivially easy (for those who like and have an idea of DIY and small repairs). The fit is perfect. So far zero problem and the lags work perfectly in combination with Motul 10W oil.

Review translated automatically

Reliable opinion

2025-08-03, 20:59

View original

Aksel

Have used these gaskets for the valve cover screws and they do exactly what they are supposed to. They seal tight, keep oil in and seem like a definite improvement over worn original gaskets. Installation was easy and the material feels both resilient and durable. No signs of oil sweat after installation - completely satisfied!

Review translated automatically

Reliable opinion

2020-07-08, 19:23

View original

Waldemar

My machine is an 86 Honda Shadow VT 1100 . Purchased parts were not dedicated for this vintage , so as a novice user I bought blind and surprisingly they fit . Installation was no problem and the material and workmanship flawless . G Moto and product on pistket . LWG .

Review translated automatically

Reliable opinion

2017-07-11, 09:59

View original

Mariusz

I am a happy owner of a yamaha yzf 125r in which I recently noticed oil loss , I replaced the valve seals which I ordered from gmoto and I am very satisfied , solidly made . Easy to install and fit to my 2010r modelj recommend to everyone.

Review translated automatically

Reliable opinion

2017-07-11, 09:59

View original

Mariusz

I am a happy owner of a yamaha yzf 125r in which I recently noticed oil loss , I replaced the valve seals which I ordered from gmoto and I am very satisfied , solidly made . Easy to install and fit to my 2010r model I recommend to everyone.

Review translated automatically

Reliable opinion

2021-08-08, 10:10

View original

Klaudiusz

Honda CBR 1100XX Super Blackbird from 1997, the replacement went without a problem, the bearings and seals fit. After replacement, you can feel a big improvement and much lighter handling. The old bearings were worn and jumped into the "point" when straightening the steering wheel, now there is no such thing.

Review translated automatically

Reliable opinion

2017-05-15, 22:44

View original

Maciej

Patient Honda CB600F Hornet, vintage 2001, non-functioning fan switch. What can I say, a top-notch product. After replacement, the fan spins and works at its best. This radiator fan switch is a great product, I would recommend it to anyone

Review translated automatically

Reliable opinion

2025-05-06, 07:08

View original

Fabian

I love the K&N oil filters. Most people screw them on with an open-end wrench and are surprised when they start leaking. Tighten them by hand and remove them again with the open-end wrench. Never had any problems. Only good experiences.

Review translated automatically

Reliable opinion

2016-03-18, 21:30

View original

Rafał

Honda Shadow VT 750 Black Spirit RC48 2003. The filter compared to the previous one I had installed has a nut, which makes it much easier to install /remove the filter, in the absence of a special key for installation. Definitely a plus.

Review translated automatically

Reliable opinion

2021-03-31, 10:03

View original

Dominik

The seals look decently made. We'll see how with their durability. I'll admit that there were problems with installation and it took some time, but they are finally sitting in place. Now only field tests.

Review translated automatically

Reliable opinion

2025-07-02, 08:12

View original

Iñaki

It works correctly and was very easy to install. My bike is a 2006 CBF600N and I had no problems at all, it only takes a socket wrench and needle nose pliers to remove and attach the connecting cable.

Review translated automatically

Reliable opinion

2017-11-17, 07:02

View original

Jakub

We fitted the bearings to a 2004 Honda Hornet pc36. The installation went smoothly and the bearings seem indestructible ;) Well, but this is Mc International after all, the top shelf among parts for Japanese ;)

Review translated automatically

Reliable opinion

2023-05-29, 13:07

View original

Mariusz

When it comes to oil filtration in our motorcycles, K&N is simply in a class of its own. I've been using them forever and although it's just a filter I can't imagine another one in my machine. I recommend.

Review translated automatically

Reliable opinion

2022-01-18, 20:35

View original

Sławomir

Filter hiflo 303 RC, standard height, throughput to be evaluated, as I wear it out I'll see if the only difference is the key cap on the body, although at first glance it looks similar. We'll see.

Review translated automatically

Reliable opinion

2018-07-17, 12:36

View original

Jakub

Honda vfr750f from 1996. Everything works perfectly. The installation went without any complications I did 2000km a week after installing the new clutch and I have no reservations.

Review translated automatically

Reliable opinion

2021-06-03, 15:15

View original

Sławomir

I own a 2005 Honda CBF600. The sensor fit without a problem, plug and play. The replacement took 5 minutes. Fulfillment of the order was lightning fast, the product was with me the next day. Highly recommend.

Review translated automatically

Reliable opinion

2021-01-24, 16:53

View original

Bogdan

I own a motorcycle honda CBR 1000F, vintage 1966, capacity 1000 cm. This is another filter from this manufacturer that I bought, and I have never had any problems with them have always served their purpose.

Review translated automatically

Reliable opinion

2022-01-11, 15:35

View original

Wojciech

XL 600VA 1987 Oil easy to use does not require instructions. I recommend this product. Very good quality product for its price. Quick delivery hassle-free service. I recommend

Review translated automatically

Reliable opinion

2025-09-02, 18:25

View original

Tomáš

The above set of seals for front forks Honda Deauville NT 700 V, r.v. 2008 absolutely fine, trouble-free assembly, the product suits the type of moto, appears to be of good quality.

Review translated automatically

Reliable opinion

2025-03-01, 08:08

View original

HOCMERT

20/20 The product corresponds to 100% of my expectations, my entire order was carefully packaged and delivery was very fast. You can order with your eyes closed.

Review translated automatically

Reliable opinion

2020-03-30, 20:44

View original

Michał

The protections, compared to the old ones, are slightly wider, more rigid and more "expandable", which makes them fit perfectly into the groove in the lade blocking the sealers.

Review translated automatically

Reliable opinion

2025-07-15, 05:30

View original

KARLOS

Same as the original, but 75% cheaper. Quick response to e-mails. Although with a little more delay in delivery with respect to what was said on the page.

Review translated automatically

Reliable opinion

2023-09-11, 20:14

View original

sara

This mounting rubber is a great replacement for the rubbers found on the Honda CBR 600, but they are slightly smaller than the original (I personally didn't mind the installation)

Review translated automatically

Reliable opinion

2025-09-25, 07:32

View original

Славчо

They did a perfect job for me.The delivery was fast and accurate.And the workmanship itself is perfect the quality is top,the site is very good and accurate and quality which is the most important thing

Review translated automatically

Reliable opinion

2019-01-14, 11:45

View original

Łukasz

Hello, The filter I purchased meets my expectations. Easier to install than standard filters. I am very satisfied and recommend, Greetings

Review translated automatically

Reliable opinion

2018-03-05, 18:27

View original

MARCIN

Hello, I bought this filter for oil change in my motorcycle i.e. 2006 Yamaha Stratoliner 1900. I have been using this product for about 5 years and am satisfied with it.

Review translated automatically

Reliable opinion

2024-09-24, 06:41

View original

Tomasz

The filter performs its function perfectly, after pouring off the old oil you can not see any flecks, etc. Thanks to the flexible gasket, I tighten it by hand and nothing leaks.

Review translated automatically

Reliable opinion