Motorcycle parts
Yamaha XP 500 T-Max - Page 7

2018-11-01, 20:15

View original

Krzysztof

I ordered the air vents with the motorcycle Honda XRV 750 Africa Twin - 1999 in mind. They fit the front calipers as well as the rear caliper. After screwing in, there is a little bit of thread sticking out(this is for a small minus), which is covered by a blanking rubber. They successfully replace the original, which is twice as expensive in the service. To the aesthetics and solidity rather can not be complained about - no burrs, the layer of zinc is placed on well-prepared steel. When tightening, care should be taken to select a perfectly matching wrench, scratches and destruction of the zinc layer can result in the appearance of rust in a fairly short time due to the fact that the material is steel. The downgrade for the material is due to the fact that I would prefer stainless steel instead of steel and zinc.

Review translated automatically

Reliable opinion

2020-04-12, 13:22

View original

Piotr

The product perfectly replaces the original part, after replacement the pump is tight. For this operation, it is worth buying a gasket and oring.

Review translated automatically

Reliable opinion

2020-06-03, 11:54

View original

Adrian

Mounting pin, fitted very well to the fairing of a Yamaha fz 8 motorcycle. The transaction went smoothly, fast delivery.

Review translated automatically

Reliable opinion

2019-03-31, 12:52

View original

Michał

The GS 500 motorcycle is a machine that I use every day. It gets no concessionary fare and has to endure all sorts of roads. Sometimes fast riding on the expressway, sometimes touring on rough and bumpy roads. The result of this effort is a broken head frame bearing, which bravely endured all the forces acting on the motorcycle. It was time for a bearing from the proven Tourmax company, which I got very quickly thanks to the Gmoto.pl store. The package came quickly, well packed. Goods of the highest quality. Since the replacement of the bearing nothing has happened to the motorcycle and you can confidently continue the season.

Review translated automatically

Reliable opinion

2019-04-13, 21:13

View original

Mariusz

I am a very satisfied owner of a 1995Yamaha XJ 900 Diversion motorcycle.The vehicle is absolutely trouble-free but due to its age, the swingarm bearings had to be replaced.I purchased a set of Tourmax bearings.The bearings and the simmering rings supplied in the set matched perfectly which made the replacement a pleasure.Now my equipment rides like new again.I would recommend this set to anyone who has a similar fault to eliminate in their equipment.If all the parts were made with such accuracy, I could boldly become a mechanic ;)

Review translated automatically

Reliable opinion

2020-04-14, 09:01

View original

Mateusz

Although it was out of stock the delivery came within 2 days of ordering. It was the first time I used the site ,,GMOTO.PL '' and certainly not the last. Entering the site everything is clear very nice to look for parts. Very big plus :) There was always a problem to which store to go to buy oil , candles , filter. Now I do not have to worry about it. I recommend Matthew YAMAHA XT660X 05'

Review translated automatically

Reliable opinion

2021-02-16, 11:19

View original

Oleksandr

I have a Yamaha XJR 1300 motorcycle and needed sealers and hoods for the lags. The hoods in the front suspension were still original and I just wanted the look to stay the same. Because of this and I bought this kit. And plus it turned out to be a good quality product. Hoods and sealers quite flexible and fit perfectly in their places. I am very satisfied. I recommend.

Review translated automatically

Reliable opinion

2016-09-09, 10:49

View original

Rafał

I bought this kit in the store with the information that it may not fit the cbr 250 but I made an aluminum ring on the wall 0.65mm height 0.80 mm circumference 30.00mm inner circumference 28.70 and it fits the rest of the dimensions is the same thank you for reliable information seller price in the service is 240 PLN and the ring cost me 10 PLN at a friend turner and everything is fine I recommend

Review translated automatically

Reliable opinion

2020-05-03, 00:23

View original

Maciej

Wsk 125 The frame is nice, you can't expect more from a plastic metallized one. It fits my wsk-i nicely. The only big minus is that it did not fit completely in the holes - I had to widen the holes with a drill both at the top and bottom. Other than that, installation was easy. I recommend the product for those who don't mind making up holes.

Review translated automatically

Reliable opinion

2024-12-05, 18:19

View original

ΑΝΔΡΕΑΣ

Thank you for shipping the correct parts that I ordered for my motorcycle.Everything was delivered in the best condition possible.Im very pleased with your team and management.The shipment was very fast and very cheap.All the parts were suitable and they were exactly what I ordered.Thank you a million.Andreas from Greece

Review translated automatically

Reliable opinion

2024-08-27, 10:29

View original

mateusz

Elegantly, my motorcycle again chatters as it should, relative to the original I see no difference. Fits perfectly nothing sticks out of the place provided by Yamaha designers. The screws go into their place. In the case of fz6N without stress you can replace this part yourself under the block.

Review translated automatically

Reliable opinion

2021-05-08, 07:38

View original

Andrzej

Plastic license plate frame looks like a good chrome material I changed the plate because I became the owner of a Suzuki Intruder VL 125 2000 year all in all. Looks super material fine that's why the price very low ugly comes longer.

Review translated automatically

Reliable opinion

2021-02-09, 10:48

View original

Marcin

Seemingly just a pin however, it allows even a 20 year old motorcycle to retain its original appearance. They do not differ in appearance and quality at all from those originally used for the installation of fairings in my 2000 Hayabusa.

Review translated automatically

Reliable opinion

2020-09-20, 14:21

View original

Rafał

Honda XL 125 Varadero year 2006. fairing mounting pin fits perfectly, made very solidly, made of strong plastic material. Matched very well to the original, virtually indistinguishable.

Review translated automatically

Reliable opinion

2019-06-17, 07:58

View original

Damian

In the category of quality/price very nice frame. Strong plastic imitating chrome. Aesthetics at a high level. Lightweight and durable And the license plate enters on contact ( for me a plus because there is no slack). I recommend

Review translated automatically

Reliable opinion

2023-12-30, 08:43

View original

Marcin

The part is of very good quality, comparable to the original, everything fits as it should, works flawlessly, you can confidently drive a few seasons without looking, doing an average of up to 10,000 km per season

Review translated automatically

Reliable opinion

2022-01-27, 10:50

View original

Sławomir

The pins fit the rump (including the plastic filling for the tail lamp) on the Suzuki SV650n K8. They perfectly replace the lost originals - there is no play, they do not fall out and do not break in the hands.

Review translated automatically

Reliable opinion

2019-12-24, 07:54

View original

Robert

VARADERO XL 1000 SD01 99r. Very good quality fuel pump repair kit. The installation went without any problems. Very good fit of the parts. I recommend the manufacturer and seller.

Review translated automatically

Reliable opinion

2022-07-23, 13:57

View original

Wiktor

Honda Varadero 125 2007r (polift) The pin looks and fits the same literally dot to dot as the original. So I confidently recommend the more that the price is better than in ASO

Review translated automatically

Reliable opinion

2017-09-04, 10:25

View original

Mariusz

frame very nice, put on jawa ts 350 looks very good on this motorcycle, installation also very pleasant immediately changes the name of the motorcycle adds better charm

Review translated automatically

Reliable opinion

2023-07-28, 07:41

View original

Adam

Parts ok . Installed in Yamaha XT 660 X. However, it is also worth replacing the oil sealer which is not included in the set. Customer service super and shipping lightning fast.

Review translated automatically

Reliable opinion

2024-09-25, 05:27

View original

Filip

Very good solution for those who want to replace the license plate frame with a new one. The price is very affordable. The quality of workmanship is also flawless. I can recommend

Review translated automatically

Reliable opinion

2019-06-10, 20:27

View original

Wojciech

Fits perfectly, should be added to the oil refinisher, the cost is pennies and most often the protection is already affected by corrosion and suitable for replacement

Review translated automatically

Reliable opinion

2019-07-07, 20:55

View original

Bartłomiej

Everything ok, the pin fits nicely and holds the fairing well, even after several times of removing the fairing and driving several thousand kilometers everything holds HONDA CBR F4 2000r.

Review translated automatically

Reliable opinion

2017-07-15, 03:51

View original

Gixxer

The bearings fit very well to the frame head from a 93r gsxr 750 well made And I'm surprised the garland is metal because the previous ones I had had a plastic one

Review translated automatically

Reliable opinion

2018-12-21, 13:12

View original

Michał

Yamaha FZ6 S2 600 2008, the product is no different from the original, identical construction, installation went smoothly literally in 5 minutes. Currently it is running without complaint.

Review translated automatically

Reliable opinion

2025-04-13, 11:27

View original

NIKOS

Excellent product. It fit properly in the caliper and I no longer have any leakage from the wear and tear of the previous one. Tourmax quality comparable to the factory ones.

Review translated automatically

Reliable opinion

2024-07-05, 06:46

View original

Krzysztof

Great quality replacement, the previous protection totally corroded, I hope this will live a little. I replaced it on a DR 650 SE vintage 1996

Review translated automatically

Reliable opinion

2024-07-29, 06:37

View original

Bartosz

Very solid bearings, all metal, tightly fitted to the post, smooth operation, workmanship 10/10, , "made in Japan" speaks for itself.

Review translated automatically

Reliable opinion

2020-06-01, 17:53

View original

mariusz

yamaha diversion 600 2002 element purchased really good quality,without any problems installed in the shin of the front suspension recommend kind regards lwg

Review translated automatically

Reliable opinion

2020-11-17, 09:25

View original

Jacek

Yamaha FJR 1300, vintage 2009, the product does not differ in any way from the original or that purchased from the service. The price for it is dramatically different.

Review translated automatically

Reliable opinion

2020-11-17, 09:25

View original

Jacek

Yamaha FJR 1300, vintage 2009, the product does not differ in any way from the original or that purchased from the service. The price for it is dramatically different.

Review translated automatically

Reliable opinion

2023-11-06, 15:55

View original

Bartłomiej

Super bearing, the ciera now turns as it should, when hammering, it is better not to hit the cage because it can break down which almost happened to me 4/5

Review translated automatically

Reliable opinion

2018-05-07, 18:15

View original

Magdalena

WSK M6 B3 1982 Very good quality product easy to install. Fits perfectly, looks very good. Frame worth recommending.

Review translated automatically

Reliable opinion

2025-07-27, 08:46

View original

Eckehard

Good product delivered quickly. I searched for a while to avoid spending so much and found what I was looking for at GMOTO. That's how it should be.

Review translated automatically

Reliable opinion

2024-12-26, 03:21

View original

Uwe-Rainer

I am very satisfied with the fast delivery and would order again at any time. With kind regards U.-R. Agthe

Review translated automatically

Reliable opinion

2023-08-14, 15:03

View original

Janek

I have not yet assembled and do not know how with the fragility of the plastic, but from the outside it looks positive. On the back a slight unpainting.

Review translated automatically

Reliable opinion

2020-11-07, 21:27

View original

Robert

Yamaha xvz12TD. Everything fits. The old ones unfortunately corroded. Thank you. I will definitely come back to you.

Review translated automatically

Reliable opinion

2024-11-07, 08:28

View original

Furui

Delivered as ordered. Everything in order. I would order from GMoto again. It is a reliable supplier.

Review translated automatically

Reliable opinion

2020-05-25, 21:10

View original

Paweł

The frame mounted on the motorcycle and from today it pleases the eye, I did not want to drill the boards and with the product I am satisfied.

Review translated automatically

Reliable opinion