Forgot password
Order status
Free delivery from 150 euro
Motorcycle cylinders - Page 5
Most popular manufacturers
Manufacturer
Price
Sort
Options +1 
Inne warianty:
Inne warianty:
Inne warianty:
Inne warianty:
pojemność:
Inne warianty:
Inne warianty:
Inne warianty:
Podobne :
from 23
Browse Motorcycle cylinders - Page 5 by manufacturer
Products reviews
The cylinder is made very well, but after machining the edges of the channels are sharp and I gently sanded them with a file and I did the same with the rings when the piston is pushed down at the end it falls very slowly, which means that the fit is very good, very fast delivery I have ordered several times from gmoto and there is really no problem I recommend to everyone I greet customers and employees of the store
Review translated automatically
Reliable opinion
I bought because my old cylinder seized up. On this cylinder I drove 200km and it also seized up I do not recommend. Does anyone know if it is returnable
Review translated automatically
Reliable opinion
Very good product for my scooter. Fits perfectly scooter Kymco super 8 50 2t. The scooter collects very nicely and runs nicely.
Review translated automatically
Reliable opinion
Motorcycle k-650 from 1970, Almot brand does not need to be recommended to anyone, a top-shelf product, the pin matched after a slight heating of the piston can be pressed in with fingers with slight resistance, the fit of the piston with the cylinder at 0.07mm(which is as it should be). And most importantly - the rings finally changed from another supplier(the previous ones added to the kit could be thrown in the trash), fitted on the locks as written in the professional literature. After assembling the engine(obviously a complete overhaul with all the rigors) - left cylinder 8.5Atm, right 8.6Atm. The engine fired up in 2 kicks, after driving 150km - it runs nicely, no smoke. I recommend Almot product as much as possible.
Review translated automatically
Reliable opinion
WSK 125. The cylinder looks Ok , the piston is like that , I pushed the pin through the piston by hand , but I didn't check it all at work because .The pin is oversized , about 2 mm . I sanded . Unfortunately , this is not the end of the trouble because one ring goes into the cylinder on contact , zero play , and the other is again oversized . Gentlemen please , do not write that I can return the goods , etc . Opinions about pins too long I have already seen here , you do nothing about it . Where do you get such good product reviews from? I suggest you throw out all the imperfections and put on the goods produced with standards , because you do not sell broom , but parts for unicycles .
Review translated automatically
Reliable opinion
mounted to honda xr125l, only need to grind the crankcases / turn the cylinder on the lathe to fit the crankcases, because the cylinder skirt has a larger diameter than the crankcases will fit. The cylinder fits nicely, it runs, you can already see the power furniture in the lower revs. The piston knocks, the piston knocks, it's not the valves or anything, it's the piston. Because the clearance between the piston and the cylinder is too big. It's generally supposed to be around 5 hundredths of a millimeter, but I measured 33 hundredths from the bottom of the piston and 63 hundredths from the top of the piston. The piston is hard to find, I found one here on the eshop, so I just pray it comes and has the right dimensions, that mine in the kit was just a dud...
Review translated automatically
Reliable opinion
Jawa 50 Mustang 79r. The cylinder from the outside cast quite well , inside there are no some scratches or bumps. The piston fits the cylinder very well. Suggesting the ad does not say in it that the pins are included, and in the photo they are shown as well after delivery they are included, which may confuse the buyer and will buy a separate set. Recommended.
Review translated automatically
Reliable opinion
Not only that there are some inconsistencies with the output of the exhaust elbow under the model keeway hurricane 2009 ( although according to the store it fits ) to this is POWER FORCE BASIC. With an inferior quality piston sold at the price of a normal power force and nowhere is it described which is misleading. Be on the lookout
Review translated automatically
Reliable opinion
Romet Ogar 205, 50 ccm3, prod year 1991. Perfectly made, from the now available larger range of materials, more suitable for the construction of a properly working engine. The set perfectly fitted. The biggest connoisseur will be satisfied. Fires, quenches, right ,left. Recommended.
Review translated automatically
Reliable opinion
Hi. I purchased a cylinder for WSK 125 as a set . I must emphatically state that it was made and solid material . It will certainly serve me for a long time. Everything fits perfectly and presents itself beautifully . There are not the slightest problems with the assembly .
Review translated automatically
Reliable opinion
This is the second set I bought, very good quality workmanship, the set is complete, as I drive through the countryside all the girls look at me, so nicely the engine runs on this piston and cylinder not to mention the pin.
Review translated automatically
Reliable opinion