Forgot password
Order status
Free delivery from 150 euro
Motorcycle engine - parts
Romet Komar 50 - Page 4
Manufacturer
Price
Sort
Options +2 
Browse by manufacturer
Products reviews
The purchased kit produced by Almot looks really promising. I think that the increased capacity of the kit should revive this little engine a bit. For those who will still have doubts, I refer you to the following link, where I have prepared a small review and comparison with the factory ZMD kit. http://motomaniacy.com/viewtopic.php?f=1&t=36327&p=502577#p502569
Review translated automatically
Reliable opinion
Komar 232 engineS38 the shaft fit without any problems well made,I would add to the shaft nuts on the clutch side as there is a changed diameter/as a kit ready to install/
Review translated automatically
Reliable opinion
komar sport 2361 engine s38 - the shaft fits perfectly, milling cutters made very well, with comments on the product - the shaft has threads with diameters fi-10 and some komar clutch had a nut fi-8. The outer bearing on the side of the magnet went in with play (it moved on the stub of the shaft) - I used glue to set the bearings, the width of the hole for the wedge too small - neither the new wedges bought at gmoto nor the wedge removed from the old shaft could fit (you need to slightly grind the wedge). I know that I could complain about the goods and it would certainly be considered favorably ( I have already complained about the goods in the past and it works very well). At the moment the engine works flawlessly, we will see how it will be with durability :).
Review translated automatically
Reliable opinion
The shaft out of the box was meticulously intended. The journals were in tolerance, the cone for the flywheel was correct, the position of the wedge was correct, the multi-milling for the clutch basket carrier was correct, the radial and axial clearances of the connecting rod were correct, and finally the shaft was checked in the claw jig - the maximum run-out on the journals was 0.01. I bought 3 pieces and none of them caused problems, customers of my workshop do not complain about this component. I recommend
Review translated automatically
Reliable opinion
Included all the components. The fit of the piston, rings, cylinder ok, the kit almost p&p. There was a problem with the installation of the piston (security from the kit poor, not very precise, do not wedge properly in the piston). I bought others on the spot and hula. In general, the product I recommend, but it is worth buying a better safety devices right away.
Review translated automatically
Reliable opinion
Hi I am Patryk and I own a 1962 WSK 125 m06 z2 , and I buy all parts and accessories from GMOTO. The parts are always matched and good quality.They are well packed and protected in the package. I highly recommend this store just in time to buy parts for our vintage motorcycles.Regards
Review translated automatically
Reliable opinion
It is slightly lighter than the original, workmanship very good, fits perfectly except for the thread on the clutch basket I Magento. It is slightly larger than the original so when replacing the shaft it is mandatory to select new nuts. Finally the engine assembled, I works perfectly :)
Review translated automatically
Reliable opinion
komar sport 2361 engine s38- undersized simmerers - did not want to fit into the sockets in the crankcase, broken when trying to install - they had too large outside diameter (I bought others and with the installation there was no problem)
Review translated automatically
Reliable opinion
Romet Motorbike 1987. bearings perfectly matched to the wheels, well protected against the possible entry of dirt, the axle runs smoothly translated in the wheel. does not block and does not cut.Greetings and Recommend.
Review translated automatically
Reliable opinion
No safety features for the piston. They blew my deadlines due to stupid safety features, probably no one checks before shipping the ordered goods. I lost in the eyes of the customer
Review translated automatically
Reliable opinion
My bike is an yamaha xt350 of 1991.The Part is like as advertised. The material used in the part it is of good quality. Transport to Portugal very fast. Recommend
Review translated automatically
Reliable opinion
The bearing is very good quality, works great, works like a dream. Price is very good, it is hard to find such a bearing at such a price for such quality. I recommend
Review translated automatically
Reliable opinion
I buy parts for WSK, everything comes very quickly, the contact is very good, the seller is helpful, I recommend 100%.
Review translated automatically
Reliable opinion
Dimensions to fit Romet Ogar 200 50cm3. From what I noticed the original I had the same company and flew a few years.
Review translated automatically
Reliable opinion
So far, it works flawlessly. The Mosquito has power. It's hard to say if it is bigger than on the original. Overall, I recommend!
Review translated automatically
Reliable opinion
There is power, except for the not nice thread connecting to the muffler and the throat set too low, it's a pretty nice set.
Review translated automatically
Reliable opinion
The bearing fits I have not looked inside but I believe there is grease there which in F£T bearings must be I trust the company
Review translated automatically
Reliable opinion
Romet Komar 2351 year 78 bearing fits round engine S38 egg. Looks solid and well made.
Review translated automatically
Reliable opinion
Rear bearings for Romet Ogara 200, they fit very well fulfill their role the wheel spins lightly and quietly
Review translated automatically
Reliable opinion
Everything ok I recommend as much as possible I will definitely come back here quality good. Fast service.
Review translated automatically
Reliable opinion
Romet 50-t1 ,50 ccm, 1981. Decent workmanship.
Review translated automatically
Reliable opinion
mosquito, ok but the pin protection was missing
Review translated automatically
Reliable opinion