Forgot password
Order status
Free delivery from 150 euro
Motorcycle engine - parts
Romet Ogar 200
Options +1 
Browse by manufacturer
Products reviews
In this set you will find all the gaskets that can be placed in the engine(In my case it was a Jawa 223 engine mounted in a Romet Ogar 200 moped) , carburetor, as well as a gasket under the head and under the muffler elbow . Their great advantage is their low price, so that we can immediately buy a spare pair (in case due to a mistake we have to assemble the engine again)They are made of good cardboard and fit almost perfectly. I wrote almost, because in places such as where we put on the gearshift apparatus, or where the piston comes out, they need to be trimmed by our own hands. Such a state of affairs is, of course, understandable and poses absolutely no problem, since, after all, each of us has scissors at hand. Below I attach a photo that shows each of the gaskets purchased. I would show how they look in the already assembled engine, but for the reason that their purpose is to seal and not to be conspicuous( In the assembled engine they are almost invisible) I will, however, limit myself to the above-mentioned photo ;D
Review translated automatically
Reliable opinion
Romet Ogar 200 I overhauled the engine in the ogar and used these gaskets.The engine does not leak does not take air as well as oil.To be sure I lubricated the gaskets with silicone, but through my fault would have uneven adhesions.If you have a perfect adhesion is traditional gasket and grease.
Review translated automatically
Reliable opinion
Cool look fits perfectly to jawa 50 type 20 . I have read a lot that parts do not fit in other stores and here without any problems. I recommend shopping at Gmoto.pl due to the teleportation of packages (24 hours) and the possibility of return if something does not fit.
Review translated automatically
Reliable opinion
I have bought many products from Gmoto.pl store and I am very satisfied. All products meet and even exceed my requirements!!! Greetings to the entire Gmoto team! Keep it up :)
Review translated automatically
Reliable opinion
Romet Komar 3 1975 engine Dezamet 023 Seger looks qualitatively good, aesthetically packaged you are sure it will not get lost somewhere, it will be useful for folding engine jawoski 223
Review translated automatically
Reliable opinion
RECOMMEND !!! Store super :) have all the parts - contact satisfactory.Good quality parts - large selection Fast delivery ! ! ! Effects of work and new parts in the picture :)
Review translated automatically
Reliable opinion
The pin did not fit the piston you had to ream the piston to make the pin enter the package came to you with a broken ring I do not know if I will still buy anything from this store.
Review translated automatically
Reliable opinion
The seals are of very good quality,they are fitted, and made of good material. I recommend to all who want to pay a little extra but have a decent product.
Review translated automatically
Reliable opinion
Romet Komar 3 1975 engine Dezamet 023---Pin aesthetically packaged to the naked eye you can see that it is decent material-wise for new shafts as found.
Review translated automatically
Reliable opinion
Romet Komar 3 1975 Dezamet 023 engine Wedge dimensionally compatible and not made of "plasticine " quality and visuals ok, it will certainly fit the new shaft.
Review translated automatically
Reliable opinion
I bought the nut for a 1980 Jawka M23 with a capacity of 49 cc. The nut fits twists and even unscrews. Such a cap unscrews.
Review translated automatically
Reliable opinion
Romet Ogar 200 50 1985 Chain of good quality, fits well Has already worked quite a lot and has not stretched I RECOMMEND
Review translated automatically
Reliable opinion
Like any product in the store - good. The price corresponds to the quality, the product does its job. Identical to the original. I recommend.
Review translated automatically
Reliable opinion
Romet Ogar 200 bushing performs very well. I recommend this product as much as possible. I have no reservations.
Review translated automatically
Reliable opinion
Hello, I recently ordered bearings for the engine Java 223 and I am pleasantly surprised, putting the bearings I had a slight problem but it was the fault of the crankcase because there was a light carbon deposits did not want to enter well, but after cleaning without any problems entered one of them even fell into the snow and continued to work xd, in general nicely packed boxes are useful for storing old parts I always order from gmoto because on other sites there is no such quality and nicely packed packages everything so far that I have ordered at gmoto works GREATLY RECOMMEND everything works
Review translated automatically
Reliable opinion
Gaskets very thin, despite having the carbs in super condition like factory! No marks from screwdrivers or other unsealing tools. And so I had to use a thin layer of silicone for safety. In addition, the fit of the gaskets at an average level. Because of which, especially those from the carter, I had to "stretch" so that they fully covered the surface of the half, and not half in a given place. But it is possible to fold on it. ;)
Review translated automatically
Reliable opinion
NOTE: This is not in the description, it is only given the internal dimension of 13mm. But! After buying this bushing is required to ream it to the dimension of the piston pin. (That is, about 14.1mm) Beyond that, the outer dimension if the connecting rod is not worn in any way, it fits perfectly! (Another note, it is necessary to heat the connecting rod and cool the bushing so that it slips in without beating with a hammer or other tool)
Review translated automatically
Reliable opinion
The o-ring fits very well! Unfortunately in my motorcycle the chain rubbed the crankcase which involved welding and re-milling the place where the oring should be, after installing the item the engine no longer bleeds. The fit is very good! It mates very well with the starter shaft. Engine like new, the area around the chain and the cover at the shaft dry and clean.
Review translated automatically
Reliable opinion
Ogar 200 88' In my opinion, this is a must-have item when replacing the kick seal. The old plate was sitting so tight , that pulling it out in a state for reassembly was impossible. The plate can be pushed into place without any problem by a long 16 mm socket. It sits securely and holds the o-ring well, which means that oil leaks stopped after replacing the o-ring and plate.
Review translated automatically
Reliable opinion
If any motorcycle you have, Whether it's new or old, the one you always take care of, On Gmoto take your bearings!!! They super parts have, and will reliably help you, They take great care of the customer, in summer and severe winter. Whether you would order one part, or deliver the whole stack, You will boast in happiness today, Your fate is important to them.
Review translated automatically
Reliable opinion
As for the cylinder very good workmanship, it is made of the same material as the original , The head is also very good I have no reservations Piston also good but as for the rings I'm not 100% convinced but I could be wrong it will turn out with time, I can give feedback in a few weeks as to these rings. Regards.
Review translated automatically
Reliable opinion
Romet Ogar 200 and they fit quite well. Between the crankcases I did not use silicone and still does not leak. (but in general, in old equipment, however, between the crankcases I recommend using, in addition to the gasket, sealing compound, because it is known in what condition most of the crankcases in these equipment, but I just have in very good condition). I recommend:)
Review translated automatically
Reliable opinion
Hello, I purchased gaskets for romet ogar 200.The gaskets are really super quality and perfectly matched to their task. They are very solid and can be installed without fear. Perfectly matched and profiled which surprised me a lot. I recommend!!! Regards.
Review translated automatically
Reliable opinion
The diameter of the pin mismatched (improper fit) with the bearing in the connecting rod head of the crankshaft, which I purchased in parallel with the pin hoping to match the two parts. I reordered the other pin hoping it would fit.
Review translated automatically
Reliable opinion
I've never seen such a gasket originally on a jawa223 engine so it's a bit strange to me, but the material is aluminum so I think such a small seal will come in handy in a stallion, especially since this engine can't catch left air
Review translated automatically
Reliable opinion
Jawa mustang 1982 - the lever is aesthetically made, the chrome looks very nice on the whole lever. It is important that the lever is complete, there is no need to complete the missing parts . I think that the price is adequate to the state of things. I recommend
Review translated automatically
Reliable opinion
Jawa 50 mustang 1975. gaskets very good the engine runs perfectly.gaskets are perfectly cut what is interesting the exhaust gasket is kryngielite.it is also worth to lubricate the hermetic or some grease but for sure:)
Review translated automatically
Reliable opinion
Clutch spring protectors made very well. It took a little effort to replace them, because the springs are quite strong, but after modifying the patent (wrench) for pressing the springs, it was possible to replace them myself.
Review translated automatically
Reliable opinion
Jawa 50 mustang 78 and Jawa 50 duck 86 gaskets very good fit durable I have put together 2 engines on them and zero leaks I recommend 100% better to buy and have 100% satisfaction than to do it yourself and get frustrated
Review translated automatically
Reliable opinion
I have already purchased the second set of spring protection for Jawa 50, they work and do their job 100%. Romet has already ridden 9 months on this protection and everything works nicely and fits. I can confidently recommend!
Review translated automatically
Reliable opinion
Ogar 200 88' After replacing the oring along with the sheet metal, the oil leaks from the kick stopped. Previously I had to add about 100 ml of oil every week. After the replacement, I did not notice any , even the slightest sweating from the kickstand.
Review translated automatically
Reliable opinion
Well-fitted sits as it should only remember that under the bottom goes an oring. Also available on the site such a kit will work perfectly. Unless the shaft is badly worn then only replace the fight.
Review translated automatically
Reliable opinion
A few of the gaskets from the set are inaccurate, they need to be cut down to fit, or larger screw holes need to be cut. The gasket between the carburetors is paper. The gasket under the carburetor spigot needs to be cut off.
Review translated automatically
Reliable opinion
The set fully met my expectations. Perfect fit. Pads better than the original, they are contoured to overlap the spring, when the original ones were flat, which made installation slightly difficult.
Review translated automatically
Reliable opinion
Well, the spring as made very strong, however, the installation requires the deformation of these hooks. I wish you good luck with the installation. In general, I wish you good luck and buy these baskets and a strong binder
Review translated automatically
Reliable opinion
Ogar 200 '85 The product is weak, the piston sucks because the moped won't even start. The cylinder is ok, the head too, although the latter could have a better thread cut and the ignition chamber ground.
Review translated automatically
Reliable opinion
I own a bike jawka 50 I got it from my grandfather and with the help of gmoto store I can renovate it pozatym very wybka delivery allowed me to accelerate the renovation thank you very much
Review translated automatically
Reliable opinion
jawa 50 mustang unfortunately the head does not fit this model and makes complications with the piston so the fit of this is unfortunately poor ;/
Review translated automatically
Reliable opinion
Romet ogar type 200 super fitted piston and is solid I recommend this store gmoto pl really parts like from PRL-U
Review translated automatically
Reliable opinion
The pin is not the best fit, There is a large gap between the cylinder and the head, resulting in a lack of compression.
Review translated automatically
Reliable opinion